background image

-9-

4.  Press the lower part of the head holder removal button to attach the head holder. (Fig.21)

 

  Make the front face of the head holder face the switch side for attachment.

 

Caution

 

The head holder cannot be connected in a state where it is facing back to front.

5.   After drying, turn "ON" the switch, apply the included shaver oil to the foil and trimming blade, and 
 

after 4 to 5 seconds, turn "OFF" the switch.

 

Wipe the surfaces of the foil and trimming blade with tissue, etc., and put on the cap. (Fig.22)

 

Recommended

 

After drying, be sure to apply the shaver oil to the foil and trimming blade.

 

(This will prevent deterioration in sharpness, reduction in rotational rate of the motor, reduction in 

 

operating times, premature damage due to wear of the foil, and heat generation of the blade.)

6.  After maintenance, keep it in a place free from moisture.
 

  Leaving it in a bathroom, etc., may result in damage since condensation will occur 

 

  inside the main body.

7. Prevent deterioration of the battery.
    Prevent deterioration of the battery.
    If you do not use the shaver for 3 months or more, discharge until the remaining battery level 
    indicator lamp “EMP” flashes, and then charge for approximately 45 minutes.

2.  After washing with water, wipe off water droplets on the main body, and attach the head holder.
 

  Lightly wipe off water droplets on the blade surfaces with tissue, etc.

3.  Mount the main body on the LED light dryer. (Fig.24)
 

Set the main body as its front (switch side) faces front and its blade surfaces face down.

 

Caution

 

  Wipe off water droplets adhered to the main body and foil surface.

 

  Be careful because the main body may topple over if tilted forward.

 

  Use this shaver exclusively.

4.  Press the dry switch.
 

During drying, the dry switch lights in blue and the light emitting lens lights in purple, 

 

and the fan rotates. After drying, the light emitting lens lights in purple for approximately 

 

15 hours, and the inscription “G-SWORD” on the LED light dryer flashes slowly 

 

(at intervals of 2 seconds) and then goes out.

    The drying time is approximately 1.5 hours. After completion of drying, it automatically 
    switches to the LED light antibacterial mode, and the LED stays lit for approximately 
    15 hours.

 

(If the ambient temperature is under 15°C, it will be detected by the sensor, 

    with the result that the drying time will become approximately 3 hours, followed by the 
    LED light antibacterial mode for approximately 15 hours.)
  Note
  If the dry switch is pressed when the main body is not set properly, the inscription 
  “G-SWORD” on the dry switch flashes quickly.

 

Set the main body again.

This mark means suitable for cleaning under an open water tap.

Drying with the LED light dryer  

(Included in the RM-LTX7000DY)

 

The main body and trimming blade cannot be dried.

 

Use at an ambient temperature of 15

35 

Υ

 or more.

1.  Connect the power adaptor to the LED light dryer and an outlet. (Fig.23)
 

Caution

 

  Do not block the suction slot.

 

  Keep out of the reach of children.

Suction slot

Front (Notched side corresponds to the back side.)

Push in the head holder until it clicks.

3.  After washing with water, wipe off water droplets on the main body and head holder.
 

Lightly wipe off water droplets on the foil surfaces with tissue, etc.

 

If wiping off is insufficient, water droplets may remain.

 

CAUTION

 

  Never drain it by shaking. (Cause of the foil-cutter assembly coming off)

Summary of Contents for RM-LTX7000






























Reviews: