manualshive.com logo in svg

Hitachi RAS-3HVRNME-AF, Installation And Operation Manual, Page: 38 / 40

Share
Download
Hitachi RAS-3HVRNME-AF Installation And Operation Manual Download Page 38

PMML0205A rev.4 - 11/2012

38

Alarm 

Code

Retry Stop 

Code

Origin

Detail of Abnormality

Main Factors

11

-

Indoor Water inlet thermistor abnormally (THM

WI

)

Loose, disconnected, broken or short-circuited connector

12

-

Indoor Water outlet thermistor abnormally (THM

WO

)

Loose, disconnected, broken or short-circuited connector

13

-

Indoor Indoor Liquid Pipe Temp Thermistor Abnormality (THM

L

) Loose, disconnected, broken or short-circuited connector

14

-

Indoor Indoor Gas Pipe Temp. Thermistor Abnormality (THM

G

) Loose, disconnected, broken or short-circuited connector

15

-

Indoor Water outlet C2 thermistor abnormally (THM

WO2

)

Loose, disconnected, broken or short-circuited connector

16

-

Indoor Water DHWT thermistor abnormally (THM

DHWT

)

Loose, disconnected, broken or short-circuited connector

17

-

Indoor Swimming pool thermistor abnormally (THM

SWP

)

Loose, disconnected, broken or short-circuited connector

18

-

Indoor Water outlet boiler thermistor abnormally (THM

WO3

)

Loose, disconnected, broken or short-circuited connector

20

-

Outdoor Compressor-Top Temp Thermistor Abnormality

Loose, disconnected, broken or short-circuited connector

21

-

Indoor 2nd ambient thermistor  abnormally (THM

AMB2

) 

Loose, disconnected, broken or short-circuited connector

22

-

Outdoor Outdoor Temp Thermistor Abnormality

Loose, disconnected, broken or short-circuited connector

24

-

Outdoor Outdoor Heat Exchanger Liquid Pipe Thermistor

Abnormality

Loose, disconnected, broken or short-circuited connector

31

-

Outdoor Indoor/Outdoor Combination Setting Error

Outdoor/Indoor Unit capacity setting error, Indoor total 

capacity excessively large/small

35

-

Outdoor Indoor Unit Number Setting Error

Indoor units with the same number exist in a refrigerant 

piping system

38

-

Outdoor Outdoor Protection Detection Circuit Abnormality

Outdoor PCB abnormality, Error in wiring to outdoor PCB

41

-

Outdoor Cooling Overload

Outdoor heat exchanger clogging/short circuit, Broken 

outdoor fan motor

42

-

Outdoor Heating Overload

Outdoor heat exchanger clogging/short circuit, Expansion 

valve close-locked

47

15

Outdoor Suction Pressure Decrease Prevention Activated

Shortage or leakage of refrigerant, piping clogging, 

Expansion valve close-locked, Fan motor locked

48

17

Outdoor Overload Operation Protection Activation

Cycle abnormality, Inverter PCB abnormality, DM 

abnormality, Heat exchanger clogging, etc.

51

17

Outdoor Inverter Current Sensor Abnormality

Error in CT wiring, Outdoor PCB abnormality, Inverter 

PCB abnormality

53

17

Outdoor Inverter Module Error

Compressor, ISPM abnormality, Heat exchanger clogging, 

etc.

54

P7

Outdoor Inverter Fin Temp. Abnormality

Fin thermistor abnormality, Heat exchanger clogging, Fan 

motor abnormality

55

18

Outdoor Inverter Non-Operation

Inverter not operating or broken

57

Outdoor

Abnormality of fan motor protection (DC fan motor)

59

-

Outdoor Inverter Fin Temp Thermistor Abnormality

Loose, disconnected, broken or short-circuited connector

b1

-

Outdoor Error in Address/Refrigerant System Setting

Address/refrigerant system setting over 64

EE

-

Outdoor Compressor Factor Alarm

Alarm to notify damage to compressor occurs 3 times 

within 6 hours

70

P-70

Indoor Hydraulic alarm

Water pressure or water flow is not detected in the 

hydraulic cycle

71

-

Indoor Water Pump Feedback

72

-

Indoor Thermostat Heater Alarm

High temperature is detected in Electric Heater T>75ºC

73

-

Indoor Mixing over-temperature limit protection for Mixed

circuit.

Circuit 2 supply temperature > Target tempe 

offset

74

P-74

Indoor Unit over-temperature limit protection

75

-

Indoor Freeze Protection by Cold water inlet, outlet

temperature detection

76

-

Indoor Freeze Protection Stop by indoor liquid temperature

thermistor 

77

-

Indoor Opentherm Communication failure

No Opentherm communication for a continuous period of 1 

minute.

78

-

Indoor RF Communication failure

There is no communication for 1 hour with one or two RF 

receivers which are bound to the RF-Bridge.

79

-

Indoor

-outdoor Unit Capacity setting Error

There is no concordance between indoor outdoor unit 

capacity 

80

-

Indoor-

LCD

LCD H-link transmission error

No H-link communication for a continuous period of 

1 minute between Indoor and LCD User control by 

connection wiring (breaking, wiring error, etc.)

81

-

Indoor Incorrect PCB operation

TROUBLESHOOTING

Summary of Contents for RAS-3HVRNME-AF









































Reviews:

No comments