background image

– 2 –

SAFETY PRECAUTION

Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

Pay special attention to signs of “   Warning ” and “  Caution ”. The “Warning” section contains

matters  which,  if  not  observed  strictly,  may  cause  death  or  serious  injury. The “Caution”  section

contains matters which may result in serious consequences if not observed properly. Please observe

all instructions strictly to ensure safety.

The signs indicate the following meanings. (The following are examples of signs.)

Please keep this manual after reading.

This sign in the figure indicates prohibition.

Indicates the instructions that must be followed.

WARNING

CAUTION

Do not reconstruct the unit.

Water leakage, fault, short circuit or fire may occur if you reconstruct the unit by

yourself.

Please ask your sales agent or qualified technician for the installation of your

unit.

Water leakage, short circuit or fire may occur if you install the unit by yourself.

Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the

earth  line  of  telephone.  Improper  installation  of  earth  line  may  cause  electric

shock.

Be sure to use the specified piping set for R410A. Otherwise, this may result in

broken copper pipes or faults.

A circuit breaker should be installed depending on the mounting site of the unit.

Without a circuit breaker, the danger of electric shock exists.

Do not install the unit near a location where there is flammable gas.

The outdoor unit may catch fire if flammable gas leaks around it. Piping shall be

suitable supported with a maximum spacing of 1m between the supports.

Please ensure smooth flow of water when installing the drain hose. If any failure

is found in the drain path, water drops from the indoor and outdoor units, causing

wet household effects.

Make sure that a single phase 240V power source is used.

The use of other power sources may cause electrical components to overheat

and lead to fire.

PROHIBITION

CONNECT EARTH LINE

PROHIBITION

PROHIBITION

Should abnormal situation arise (like burning smell), please stop operating the

unit and remove plug from the socket or turn off the circuit breaker. Contact your

agent. Fault, short circuit or fire may occur if you continue to operate the unit

under abnormal situation.

Please contact your agent for maintenance.

Improper self maintenance may cause electric shock and fire.

Please contact your agent if you need to remove and reinstall the unit.

Electric shock or fire may occur if you remove and reinstall the unit yourself improperly.

WARNING

PRECAUTIONS DURING INSTALLATION

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

“OFF”

PROHIBITION

Avoid an extended period of direct air flow for your health.

Do not connect the power calbe with an extension cable or do not plug too many

leads of the other electric appliance into the socket where this cable is plugged.

In addition, wire the cable with some allowances to prevent the cable from stretching.

Not doing so will cause an electrical shock, heat generation or fire.

PROHIBITION

Do  not  put  objects  like  thin  rods  into  the  panel  of  blower  and  suction  side

because the high-speed fan inside may cause danger.

Do not bundle the power cable, pull it, put something on it, heat it, process it, or

put it between things. Breakage of the power cable may result.

Use of a damaged cable may cause an electrical shock or a fire.

PROHIBITION

PROHIBITION

Summary of Contents for RAC-25YHA2





















Reviews: