■
How to remove the door of the Vacuum Case
43
1
2
3
Be sure to remove foods contained in the Vacuum Compartment.
Remove the Vacuum Case (with the door) fi rst. Remove the door of the Vacuum Compartment and the vacuum packing in the following
way, and then maintain/care them. Do not remove other things except the door of the Vacuum Case and the vacuum packing.
●
If
真空開
-1˚C (Vacuum Compartment Subzero) /
真空開
+1˚C
(Vacuum Compartment Chiller) indicator lamps fl ash, the vacuum
function may not be in the normal conditions.
Pg.55
●
The vacuum function will not work properly if some
package of foods is pinched in or dirt/dust is adhered to
the vacuum packing or the vacuum release valve (in blue).
●
Moisture in juicy foods stored in the Vacuum
Compartment will evaporate and cause
dew condensation or frost in the Vacuum
Compartment. If water drops and/or frost
adheres inside the Vacuum Compartment or
around the door of the Vacuum Compartment,
wipe off them with a dry cloth.
●
For troubleshooting about the Vacuum Compartment, see Troubleshooting
Pg.55
●
Replace an old vacuum packing if the vacuum state can’t be kept well.
Pg.57
●
The vacuum function will not work properly if the
vacuum packing or the vacuum release valve (in blue)
comes off or is loosened.
●
Make sure to wipe off
spilled water or food soup
soon, if any. Water will be
frozen, which may lead to
a trouble of the Vacuum
Case (with the door).
Notice
Vacuum Compartment
How to maintain/care the Vacuum Compartment
How to maintain/care the Vacuum Compartment with the vacuum packing removed
●
Do not rinse the door of the Vacuum Case in water.
●
If detergents and others except lukewarm water are used to clean the vacuum packing, the vacuum packing
may be damaged, deformed or change in color, which may cause that the vacuum state can’t be kept well.
●
Loosened vacuum packing or loose-fi tting door of the Vacuum Case may cause that the vacuum state can’t be kept well.
Caution
Pay attention that no package of
the foods is pinched.
Pull the door, lift up the edge
of the Vacuum Case (with the
door) lightly and then pull it out.
Insert a plastic wrap case or
something like that under the case
so that the door of the case will
be fl oating and removable without
diffi cult.
Unset the tab at the edge of the
Vacuum Case.
Rinse dirty portion in water with a soft
wash sponge, wipe off the moisture with
a dry cloth, and then let it dry naturally.
Remove dirt in the groove of the vacuum
packing on the door.
※
Do not use the detergents, etc.
Rotate the door of the Vacuum Case
upon around the upper portion.
Hold down the door of the Vacuum
Case to unset the axis.
Rotate the door of the Vacuum
Case upon the upper side of the
door, and pull it out.
Put the Vacuum Case (with the door) back into
the Vacuum Container, and then lower the lock
of the handle.
Wipe the vacuum packing, the inside the Vacuum Case and the
packing support, using a soft cloth wet by lukewarm water.
Waste thread
Scraps
The indicator
lamp fl ashes.
Vacuum release valve
Vacuum release valve
1
1
2
3
3
4
Tab
2
2
Rotation criteria
Grasp the tab of the vacuum packing on the observer’s
upper right and remove it by hand carefully.
Align the axis of the door of the Vacuum
Case to the support.
1
1
Align the tab to the notch accurately, and
then combine them together.
3
Tab
Tab
Axis of the door
of the Vacuum
Case
Support
Notch of the groove
■
How to maintain/care the vacuum packing
■
How to install the door of the Vacuum Case
2
Pull up the door of the Vacuum Case while
holding the bottom of the Vacuum Case.
Check the tab is in place.
3
