background image

-3-

MN1-6260  Rev.2

2. Specifications and Parts name

The specifications and the name of each part are provided below.

2-1. Specifications

Application:

Cardiovascular

Type of patient contact:

Surface

Connectable instruments:

ALOKA LISENDO 880,ALOKA ARIETTA 850

NOTE:

At the time of publication of this manual, the connectable diagnostic 

ultrasound instrument or instrument software version available with this 

probe is different for each country, please refer to the instrument instruction 

manual or contact your local Hitachi representative.

Field of view:

90°

Frequency:

2.75 MHz

Cable length:

2.2 m

Service life:

3 years

Applied part:

Probe tip including ultrasonic radiation part, see the section 2-2

Part treated as Applied part:

Cable up to 1 m length from the probe tip

IPX7 range:

See Figure 1

Measurement accuracy:

Refer to the instruction manual of the ultrasound diagnostic instrument

External dimensions:

See Figure 1

Maximum surface

 Temperature of Probe tip

43

°C

Remark: The tolerance for the dimensions is ±10%.

Figure 1 External View 

Unit: mm

IPX7 range

40

50

95

Cable length

30

Summary of Contents for MXS1













Reviews: