background image

iii

MN1-6260  Rev.2

Introduction

This is the instruction manual for MXS1 probe. The probe is available by connecting to Hitachi's ultrasound diagnostic 
instrument and can be mainly used for observation of cardiovascular.
Prior to use, read this manual as well as the separate instruction manual “Safety” in which information for safe use is 
provided.  

The probe bears the CE mark but the mark is valid only when the probe is connected to the ultrasound diagnostic 
instrument bearing the CE mark.

Symbols used in this document

Safety information is classified into Danger, Warning, Caution, and Note according to the level of hazard. Those terms 
are used in safety information provided to prevent hazards and injuries to the operator or patient.

 Danger

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the 

operator or patient.

 Warning

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the 

operator or patient.

 Caution

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to 

the operator or patient, or property damage only.

 Note

Indicates a strong request concerning an item that must be observed in order to prevent damage or 

deterioration of the equipment and also to ensure that it is used efficiently.

The type of safety information is indicated by the symbols below.

 

This symbol means that attention is required.

 

This symbol means that the described action is prohibited.

 

This symbol means that the described action is mandatory.

Summary of Contents for MXS1













Reviews: