Hitachi L100 IP Series, Instruction Manual

Page: 76 / 94

Chapter 13 – The optional remote operators
13-2
The monitor mode
The following table describes the display contents. The
*
) marked column indicates whether parameters can
be changed during inverter operation (Y) or not (N).
Function Display contents
Standard
setting
Parameter
range
*
) Notes
Refer
to
Frequency set value
Set value via O/OI
Set value via pot(NA)
Jogging mode
Multistage freq. 1
...
Multistage freq. 15
FS000.0 0.0Hz
TM000.0 0.0Hz
VR000.0 0.0Hz
JG000.0 0.0Hz
1S000.0 0.0Hz
...
15S000.0 0.0Hz
0.0Hz 0.0~360.0Hz Y
Set value is displayed on the
left, actual value on the right.
In the centre an F indicates
forward run and an R indicates
reverse run.
FS : Now the set value can
be entered.
TMP , FSP , VRP , 1P~15P :
PID control active
d 01
F 01
1. Acceleration time ACC1 0010.0S F 02
1. Deceleration time DEC1 0010.0S
10.0s
(15.0s)
0.1~3000.0s Y
F 03
Frequency
source
F-SET-SELECT TRM
TRM
VR, TRM,
REM
N
A 01
Run command source F/R-SELECT TRM TRM TRM, REM N
VR: NOT IN USE!
TRM: Input O/OI
REM: Remote operator
A 02
Scaled output
frequency
/Hz01.0 01.0
1.0 0.1~99.9 Y Display only
d 07
b 86
Motor current Im 0.0A 0.0% Display only -
Displays current in A ( left )
and % of rated current ( right )
d 02
Magnetizing current
I 0 A
Rated cur-
rent
* 0.58
0~32A N b 32
Manual boost V-Boost Code<11> 11 00~99 Y A 42
Manual boost fre-
quency adjustment
V-Boost F 10.0%
10% 0.0~50% Y A 43
Boost method V-Boost Mode 0 0 0. 1 N A 41
Output voltage gain
V-Gain 100%
100 50~100% Y
A 45
Jogging frequency Jogging 1.00Hz 1.0Hz 0.5~9.99Hz Y A 38
Jogging stop mode Jog Mode 0
0 0~2 N
A 39
Analog meter adjustm.
ADJ 80
80 0~255 Y
b 81
Remote OPE-J display
contents
PANEL d01 d 01 01~07 Y b 89
Status of input and
output terminals
TERM LLL LLLLL
Display only -
d 05
d 06
ERR1 # No last trip message available
ERR1 OVER.V
Displays type of trip
(e.g. overvoltage)
ERR1 31.0Hz Frequency at time of trip
ERR1 12.5A Current at time of trip
ERR1 787.0Vdc
Voltage between P and N
at time of trip
ERR1 RUN 000001H Hours of operation at time of trip
ERR2 #
Trip history register:
ERR1 :
Last trip
ERR2 :
Last trip but one
ERR3 :
Last trip but two
ERR3 #
Display only
-
Last trip but one / last
trip but two not available
(For other displays
refer to
ERR1 )
d 08
Trip counter ERROR COUNT 25 Display only - Number of trips so far -