Hitachi HX-RIO3 Series User Manual Download Page 38

Page: 38 / 63

HX-RIO3 Series

8. Troubleshooting

How to diagnose by LED indicator

LED Status

Cause

Action

All LED turns off

- No power

- Check main power Cable

- System power is not supplied.

- Contact Sales team and send
module for repair.

MOD LED flashes green

- Failure of initialization EEPROM
parameter.

- Contact Sales team and send
module for repair.

MOD LED flashes red

- Excess of expansion slot
- Excess of IO size
- Wrong IO composition
- Occurrence of EEPROM checksum
error

- Use expansion slot up to 63.
- Compose that IO total size is not
excess.
- Check composition I/O Module

MOD LED is red

- Wrong address ID
- Occurrence critical error in firmware

- Contact Sales team and send
module for repair.

I/O LED turns off

- Failure of realization expansion
Module
- None expansion Module

- Check connector status both NA
series and expansion module.

I/O LED flashes red

-Failure of configuration baud rate

- Check communication cable with
Master
- Check power for master.

-Failure of initialization I/O

- Use expansion slot up to 63.
- Compose that IO total size is not
excess.
NA series notice unidentified
expansion module ID. Check
status of expansion module.

I/O LED is red

-Failure of exchanging I/O data

Check status of expansion IO
connection.

RUN

LED

flashed

Green

-PLC program stop

Check the toggle switch is up.

RUN LED flashed red

-Failure of Module Configuration

Check the module hardware and
software configurations are the
same.

Summary of Contents for HX-RIO3 Series
































































Search results

Summary of Contents for HX-RIO3 Series

Reviews:

Related manuals for HX-RIO3 Series

Brands by name

Popular brands

Hitachi HX-RIO3 Series, User Manual

Search results

Summary of Contents for HX-RIO3 Series

Reviews:

Related manuals for HX-RIO3 Series

Brands by name

Popular brands