Hitachi DH 25PA Technical Data And Service Manual Download Page 28

Page: 28 / 44

--- 25 ---

9-3. Tightening Torque

(1) Tightening torque of each screw and bolt

Hex. Socket Hd. Bolt (W/Flange) M5 x 25 [32] <32>

4.9 N

•

m (50 kgf

•

cm)

Hex. Socket Hd. Bolt (W/Flange) M5 x 45 [63] <66>

3.43 N

•

m (35 kgf

•

cm)

Hex. Hd. Tapping Screw D5 x 45 [58] <61>

2.94 0.49 N

•

m (30 5 kgf

•

cm)

Seal Lock Screw (W/Washers) M5 x 25 [77] <87>

2.94 0.49 N

•

m (30 5 kgf

•

cm)

Tapping Screw (W/Flange) D5 x 25 (Black) [74] <84>

2.94 0.49 N

•

m (30 5 kgf

•

cm)

Tapping Screw (W/Flange) D4 x 20 (Black) [83] <93>

1.96 N

•

m (20 kgf

•

cm)

Tapping Screw (W/Flange) D4 x 12 (Black) <81>

1.96 N

•

m (20 kgf

•

cm)

Seal Lock Screw (W/SP.Washer) M4 x 12 [52] <52>

1.96 N

•

m (20 kgf

•

cm)

Seal Lock Screw (W/SP.Washer) M4 x 8 <70>

1.96 N

•

m (20 kgf

•

cm)

Oil Cap [12] <12>

2.94 0.49 N

•

m (30 5 kgf

•

cm)

(2) Special grease

Although the newly developed grease (light yellow) is used in the Models DH 25PA and DH 25PB, the

conventional grease for hammer drill (yellow) will be supplied for the time being (Code Nos. 980927, 981840

and 308471). There is no problem even if both greases are used during servicing.

+ 1.96

+ 20

+ 1.47

+ 15

+ 0.49

+ 5

+ 0.49

+ 5

+ 0.49

+ 5

+ 0.49

+ 5

Summary of Contents for DH 25PA













































Search results

Summary of Contents for DH 25PA

Reviews:

Related manuals for DH 25PA

Brands by name

Popular brands

Hitachi DH 25PA, Technical Data And Service Manual

Search results

Summary of Contents for DH 25PA

Reviews:

Related manuals for DH 25PA

Brands by name

Popular brands