11
English
(2) Regarding the temperatures of the rechargeable
battery
The temperatures for rechargeable batteries are as
shown in
Table 2
, and batteries that have become
hot should be cooled for a while before being
recharged.
Table 2
Recharging ranges of batteries
䡬
(1) – (9) : HCS Blades (HCS : Highspeed Carbon
Steel)
䡬
(10) – (20) : Bl-METAL Blades
Refer to
Table 5, 6
and
7
for use of the blades.
Optional accessories are subject to change without
notice.
APPLICATIONS
䡬
Cutting pipe and angle steel.
䡬
Cutting various lumbers.
䡬
Cutting mild steel plates, aluminum plates, and
copper plates.
䡬
Cutting synthetic resins, such as phenol resin and
vinyl chloride.
For details refer to the section entitled “SELECTION OF
BLADES”.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latches
(2 pcs.) to remove the battery (See
Figs. 1
and
2
).
CAUTION
Never short-circuit the battery.
Table 1
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light for 0.5
seconds. (off for 0.5 seconds)
Lights continuously
Lights for 0.5 seconds. Does not light for 0.5
seconds. (off for 0.5 seconds)
Lights for 0.1 seconds. Does not light for 0.1
seconds. (off for 0.1 seconds)
Lights continuously
Before
charging
While
charging
Charging
complete
Charging
impossible
Blinks
Lights
Blinks
Flickers
Lights
Malfunction in the
battery or the charger
Battery overheated.
Unable to charge
(Charging will commence
when battery cools).
Overheat
Standby
The
pilot
lamp
lights or
blinks in
red.
The
pilot lamp
lights in
green.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2
).
CHARGING
Before using the power tool, charge the battery as
follows.
1. Connect the charger’s power cord to a receptacle.
When the power cord is connected, the charger’s
pilot lamp will blink in red. (At 1-second intervals)
2. Insert the battery into the charger.
Firmly insert the battery into the charger until the
line is visible, as shown in
Fig. 3, 4
.
3. Charging
When inserting a battery in the charger, charging
will commence and the pilot lamp will light
continuously in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (At 1-second intervals) (See
Table 1
)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown
in
Table 1
, according to the condition of the charger
or the rechargeable battery.
Temperatures at
Rechargeable batteries
which the battery
can be recharged
BSL1430, BSL1830
0°C – 50°C
Charger
UC18YRSL
Battery
BSL1430, BSL1830
Approx. 45 min.
(3) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown
in
Table 3
.
Table 3
Charging time (At 20°C)
NOTE:
The charging time may vary according to
temperature and power source voltage.
01Eng_CR14DSL_WE
6/4/08, 11:58
11
Summary of Contents for CR 14DSL
Page 6: ...5 23 27 28 29 30 21 22 25 26 24 T U 002Table_CR14DSL_WE 6 4 08 11 57 5 ...
Page 78: ...77 09Back_CR14DSL_WE 6 4 08 12 00 77 ...
Page 80: ...79 1 2 3 4 5 09Back_CR14DSL_WE 6 4 08 12 00 79 ...
Page 81: ...80 09Back_CR14DSL_WE 6 4 08 12 00 80 ...
