7
6
CP-WX1
1000 ( P6WX )
Daisy Chain Communication
Command data
①
Control the projector
byte_0
byte_1
byte_2
byte_3
byte_4
byte_5
Action
Type
Setting Code
low
high
low
high
low
high
Action (byte_0-1)
Action
Classification
Content
1
Set
Change setting to desired value.
4
Increment
Increment setup value by 1.
5
Decrement
Decrement setup value by 1.
6
Execute
Run a command.
Note: For the Type and Setting Code, see the RS-232C communication/
Network command table (
20
).
②
Get the projector’s status
byte_0
byte_1
byte_2
byte_3
byte_4
byte_5
Action
Type
Connection ID
low
high
low
high
low
high
Action (byte_0-1)
Action
Classification
Content
2
Get
Read projector internal setup value.
Connection ID (byte_4-5)
Connection ID
Content
0~255
This value is attached to the reply data.
③
Other commands
byte_0
byte_1
byte_2
byte_3
byte_4
byte_5
Action
Target Number
Connection ID
low
high
low
high
low
high
Support Command
Action
Target Number Connection ID
Get the number of connected projectors
2
0
0~255
Set the communication Group
identification and Communication ID
1
0~65535
0~255
Get the communication Group
identification and Communication ID
2
0~65535
0~255
Daisy Chain Communication
Command data
Requesting projector status (Get command)
(1) Send the following request code from the PC to the projector.
Command data (‘02H’ + ‘00H’ + type (2 bytes) + connection ID (2
bytes))
(2) The projector returns the response code to the PC.
‘9DH’ + ‘02H’ + connection ID (2 bytes) + data (2 bytes)
When the projector cannot understand the received command, the error code
is sent back to the PC.
‘95H’ + ‘02H’ + connection ID (2 bytes) + ‘00H’ + ‘00H’
When the projector cannot execute the received command, the error code is
sent back to the PC.
‘9CH’ + ‘02H’ + connection ID (2 bytes) + error code (2 bytes)
Action (byte_0-1)
Error Code
Error Code
Content
0
The command was not accepted, since the projector connected to PC was
busy.
1
Communication error is happened between projectors.
2
The command was not accepted, since the designated projector was not
found.
Changing the projector settings (Set command)
Requesting projector status (Get command)
(1) Send the following request code from the PC to the projector.
Command data (‘01H’ + ‘00H’ + type (2 bytes) + setting code (2 bytes))
(2) The projector changes the setting based on the above setting code.
(3) Projector does not send out the response data.
Using the projector default settings (Reset Command)
(1) The PC sends the following default setting code to the projector.
Command data (‘06H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)
(2) The projector changes the specified setting to the default value.
(3) Projector does not send out the response data.
Increasing the projector setting value (Increment command)
(1) The PC sends the following increment code to the projector.
Command data (‘04H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)
(2) The projector increases the setting value on the above setting code.
(3) Projector does not send out the response data.
Decreasing the projector setting value (Decrement command)
(1) The PC sends the following decrement code to the projector.
Command data (‘05H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)
(2) The projector decreases the setting value on the above setting code.
(3) Projector does not send out the response data.
Summary of Contents for CP-WX11000
