Hitachi C12FCH Technical Data And Service Manual Download Page 53

Page: 53 / 87

--- 49 ---

a The power cord is not

connected to power
supply.

b The carbon brush

wear exceeds
allowable limit (5 mm).

c Contact failure of the

micro switch

a Power supply voltage

is lower than rated
voltage.

------

• Check power supply voltage.
• Connect the power cord to
power supply.

• Check the Carbon Brushes
(1 Pair)

[262]

for wear.

• Replace the Carbon Brushes

(1 Pair)

[262]

• Check the Switch (1P Screw

Type)

[257]

for conductivity.

• Replace the Switch (1P Screw

Type)

[257]

• Check power supply voltage.
• Check if extension cord is
appropriate.

Item

Phenomenon

Cause

Factory

standard

Inspection, repair or

adjustment

Saw blade does not
rotate when switch is
triggered.

Saw blade runs too
slow (not within
3,600 --- 4,400 min

-1

a Improper wiring

b Switch (B) failure
(Only Model C 12LCH)

C Switch (A) failure

d Switching power

supply failure

e Laser module ass'y

failure

a Switching power

supply failure

b Laser module ass'y

failure

Laser marker does not
light. (Models C 12LCH/
C 12FCH)

------

• Check the wiring.

• Check Switch (B) (1P Type)

[253]

for conductivity.

• Replace Switch (B) (1P Type)

[253]

• Check Switch (A) (1P Type)

[252]

for conductivity.

• Replace Switch (A) (1P Type)

[252]

• Check the Switching Power

Supply

[249]

for conductivity,

input and output referring to
"11-4. Wiring Diagram".

• Replace the Switching Power

Supply

[249]

• Replace the Laser Module (A)

Ass'y

[12A]

• Same as item 6-(d).

• Same as item 6-(e).

Laser light is poor or
strong.
(Models C 12LCH/
C 12FCH)

Summary of Contents for C12FCH
























































































Search results

Summary of Contents for C12FCH

Reviews:

Related manuals for C12FCH

Brands by name

Popular brands

Hitachi C12FCH, Technical Data And Service Manual

Search results

Summary of Contents for C12FCH

Reviews:

Related manuals for C12FCH

Brands by name

Popular brands