Hitachi C12FCH Technical Data And Service Manual Download Page 34

Page: 34 / 87

--- 30 ---

1. Remove the Machine Screw M5 x 10 (Black)

[234]

at the notched side of the Spindle Cover

[236]

and slide the

Spindle Cover

[236]

to remove the TCT Saw Blade 305 mm-D25.4 Hole-NT32

[193]

in the next step.

2. Remove Bolt (A) M10

[191]

using the box wrench 17 mm (standard accessory). Then Washer (B)

[192]

, TCT

Saw Blade 305 mm-D25.4 Hole-NT32

[193]

and the other Washer (A)

[194]

can be removed in this order.

3. Remove Special Screw (C) M5

[230]

and Special Screw M6

[216]

, then remove the Link

[214]

4. Remove the three Machine Screws M5 x 10 (Black)

[233]

and remove Cover Plate (B) Ass'y

[220]

from the

Gear Case

[208]

5. Remove the two Machine Screws (W/Washers) M6 x 20 (Black)

[195]

. Slightly tap the Gear Case

[208]

with a

plastic hammer to remove the Spindle Ass'y

[196]

6. Perform the steps 1 to 6 in "E. Laser marker" on the next page.

7. Remove the Hex. Socket Hd. Bolt M6 x 16

[207]

. Note that the Gear Case

[208]

moves upward when the

Hex. Socket Hd. Bolt M6 x 16

[207]

is removed because the Hex. Socket Hd. Bolt M6 x 16

[207]

acts as an

upper limit stopper of the Gear Case

[208]

8. Remove the Seal Lock Hex. Socket Set Screw M6 x 10

[39]

. Holding the Gear Case

[208]

, slightly tap Shaft

(C)

[29]

to remove it. Then Spring (A)

[41]

can be removed.

9. Remove the two Machine Screws M5 x 10

[280]

. Then Lever Holder (A)

[281]

can be removed from the Gear

Case

[208]

(for Europe).

10. Remove the Nylon Nut M5

[279]

, Lever Shaft

[277]

and Lever Spring (A)

[276]

, then Lock Lever (D)

[278]

can

be removed (for Europe).

D. Vise ass'y

Tool required:

• Phillips screwdriver

Fig. 35

1. Remove the Wing Bolt M6 x 15

[137]

to remove the Vise Shaft

[142]

2. Remove the Machine Screw M4 x 10

[141]

to remove the Vise Plate

[140]

3. Remove the Knob Bolt

[136]

from the Screw Holder

[138]

Summary of Contents for C12FCH
























































































Search results

Summary of Contents for C12FCH

Reviews:

Related manuals for C12FCH

Brands by name

Popular brands

Hitachi C12FCH, Technical Data And Service Manual

Search results

Summary of Contents for C12FCH

Reviews:

Related manuals for C12FCH

Brands by name

Popular brands