manualshive.com logo in svg

Hitachi 43FDX15B, Service Manual, Page: 35 / 67

Share
Download
Hitachi 43FDX15B Service Manual Download Page 35

35

Adjustment preparation

(1) Start adjustment after the power is turned on for

20 minutes or more.

(2) The vertical incident illumination on the screen

should be 20 lux or less. (Room should be dark).

(3) Set the video settings (CONTRAST: max,

others: center) to standard condition.

(4) The blue defocus and cut off adjustments should

be completed.

(5) For low light white balance adjustment, input a

white raster signal level of 0.286 Vp-p   (Video
input level).

(6) For high light white balance adjustment, input a

white raster signal level of 0.715Vp-p (Video
input level).

(7) Confirm R and G Drive (cool) data is 3F.
(8) Set Video Advanced Settings-Color Temp-

erature to COOL.

Adjustment procedure

(1) Select the input signal for high brightness (Video

level = 0.715Vpp).

(2) Adjust the high brightness white balance by

changing I

2

C menu (R and G DRV cool mode

only).

(3) Select the signal for low brightness (Video level

= 0.286Vpp)

(4) Adjust the low brightness white balance.
(5) Check that high brightness white balance is still

obtained. If it is not, return to step (2).

White balance =

10800° K ± 0 MPCD 

Color coordinate =

x …… 0.278
y …… 0.280

Normal:

7200

˚

K

Warm:

6500

˚

K

2.15 Sub brightness adjustment

Adjustment preparation
(1) Start adjustment after the power is turned ON

for 20 minutes or more. 

(2) Receive the color bar signal.
(3) Set video conditions to factory preset.
(4) The vertical incident illumination on the screen

should be 20 lux or less. (Room should be dark).

Should sink
to black

Should rise
slightly from
black

Adjustment procedure
(1) Go to “Sub Brightness” adjustment in I

2

C

ADJUST mode (press Input and Power button
on Control panel at same time), using Cursors

, 

and then Cursor 

.

(2) Then adjust “Sub Brightness” using Cursors 

,

to increase or decrease the value, according

to figure. (Visually adjust).

(3) After adjustment, press MENU button to exit I

2

C

ADJUST mode. (Data is stored in memory).

Note:

When selecting SUB-BRIGHTNESS mode the

m

icroprocessor sets the CONTRAST and

COLOR to MIN. automatically, but make sure
that the other conditions are center. 
Directly observe the screen by eye without using
a mirror.

Y

CY G  MG R  BL

A7 A6 A5 A4  A3  A2

A1

B
C
D

Q I 

W 

100% 

BLK

W

75%

Summary of Contents for 43FDX15B




































































Reviews:

No comments