manualshive.com logo in svg

Hitachi 43FDX15B, Service Manual, Page: 25 / 67

Share
Download
Hitachi 43FDX15B Service Manual Download Page 25

25

2.6 Raster position adjustment

Adjustment preparation
(1) The set can face east or west.
(2) Input the single cross test signal.
(3) Set video conditions to factory preset.
(4) The electric focus should have been coarse

adjusted.

(5) The digital convergence RAM should be cleared

(uncorrected state). With the TV set off, press
and hold the service switch located on the
Power/Deflection  PWB and then press the
power button.

(6) Start adjustment 20 minutes or more after TV is

turned on.

Adjustment procedure
(1) Turn the centering magnets for red, green, and

blue to satisfy the condition below. The red and
blue horizontal lines should match with green.

(RED)        (BLUE)

43”  

30

30

53” SDX

20

35

53” FDX

20

35

Tolerance: ± 2mm

1

2

Adjustment procedure
(1) Receive any NTSC signal.
(2) Press the SERVICE ONLY

SW on

CONVERGENCE/FOCUS PWB and POWER to
display DCU unceorrected converge data.

(3) Locate the horizontal size VR (R711 on

POWER/DEF PWB).  Adjust horizontal size to
the table below.

Notes:

(1) Once Normal mode Horizontal size adj. is

done.  To restore old RAM data, turn TV off
and on.

(2) After adjustment, press SERVICE ONLY

switch to exit DCU crosshatch.

(3) H. SIZE adjustment is only done in

NORMAL MODE (NTSC).

=

NORMAL
MODE

43”

825

53” SDX

1000

53” FDX

1020

Tolerance: ± 5mm

Geometric
center of the
screen

R

B

(2) Upon completion of adjustment, fix centering

magnets with white paint.

NOTES:

(1) If internal cross-hatch does not appear

after clearing RAM data, press service
switch again. 

(2) To restore old RAM data, turn TV off and

on.

1

2

2.8 Horizontal size adjustment

Adjustment preparation
(1) The set can face east or west.
(2) Set video conditions to factory preset.
(3) The electric focus should have been coarse

adjusted.

(4) Start adjustment 20 minutes or more after TV is

turned on.

Notes:

(1)

If internal cross-hatch does not
appear after clearing RAM data,
press service switch again (on
POWER/DEFLECTION PWB).

(2) To restore old RAM data, turn TV

off and on.

(3) V-Size is only done in NORMAL

mode (NTSC).

= NORMAL

MODE

43”

590

53” SDX              710

53” FDX

710 

Tolerance: ± 5mm

2.7 Vertical size adjustment

Adjustment preparation
(1) The set can face east or west.
(2) Set video conditions to factory preset.
(3) The electric focus should have been coarse

adjusted.

(4) Start adjustment 20 minutes or more after TV is

turned on.

Adjustment procedure

(1) Receive any NTSC signal.
(2) Press the SERVICE ONLY

SW on

CONVERGENCE FOCUS PWB and POWER to
display DCU uncorrected convergence data.

The 6th line
from center

Between the
vertical lines
at the left and
right end.

Between the
horizontal lines 
at the top and
bottom

(3) Locate the vertical size VR (R607) on

DEFLECTION PWB.  Adjust the vertical size
according to the following table.

The 5th line
from center

Summary of Contents for 43FDX15B




































































Reviews:

No comments