Hitachi 42HDS69 - 42" Plasma TV, Service Manual

Page: 25 / 117

Securing to a table-top
1. Using wood screws (two) fasten the set to the
clamping screw holes on the rear of the Plasma
Display stand as shown below.
2. Using commercially available wood screws, secure
the set firmly in position.
Securing to a Wall
1. Keep the Plasma television 4 inches away from the
wall except when mounted using the wall mount
bracket.
2. Secure the television to the wall as shown in fig. (a)
or (b).
NOTES: 1. Do not block the ventilation holes of
the Plasma Display monitor. Blocking
the ventilation holes might cause fire
or defect.
2. In case of an abnormal symptom,
unplug the AC cord.
3. If you purchased the wall mount
bracket option, please ask for
professional installer. Do not install
by yourself.
4. If the Power Swivel feature will not be
used, the Plasma television should be
secured to the wall as shown in
fig. (a).
5. If the Power Swivel feature will be
used, the Plasma television should be
secured to the wall as shown in
fig. (b). The wires need to be long
enough to allow the television to turn
30˚ to the left and right.
Caution when moving the main unit
As this product is heavy, whenever it is moved, two
people are required to transport it safely. Whenever the
unit is moved it should be lifted forward using the top
and base on both sides of the Display Monitor for
stability. When moving the Display Monitor, lift the
handles and the bottom frame as shown below. Do not
grab the speakers or the back cover when lifting.
ANTENNA
Unless your Plasma Television is connected to a cable
TV system or to a centralized antenna system, a good
outdoor color TV antenna is recommended for best
performance. However, if you are located in an
exceptionally good signal area that is free from
interference and multiple image ghosts,
an indoor antenna may be sufficient.
LOCATION
Select an area where sunlight or bright indoor
illumination will not fall directly on the picture screen.
Also, be sure that the location selected allows a free
flow of air to and from the perforated back cover of the
set. In order to prevent an internal temperature
increase, maintain a space of 10 cm (4 inches) from the
sides/back of the monitor, and 30 cm (12 inches) from
the top of the television to the wall. To avoid cabinet
warping, cabinet color changes, and increased chance
of set failure, do not place the TV where temperatures
can become excessively hot, for example, in direct
sunlight or near a heating appliance, etc.
CONNECT POWER SWIVEL CABLE
Connect one end of cable (Arrow mark facing left) to
the swivel slot of the Plasma Rear Panel. Connect the
other end (Arrow mark facing front)to the swivel slot of
the Table Top Stand.
TURNING RADIUS
The maximum turning radius is 30˚ (left and right). Do
not place any objects on the path of the monitor when
using the power swivel feature.
To take measures to prevent the Plasma Display from tipping over and prevent possible injury it
is important to mount the unit in a stable and flat surface.
How To Set Up Your New Hitachi Plasma Television
30 cm (12 inches)
10 cm (4 inches)
10 cm (4 inches)
11.8in
(30cm)
11.8in
(30cm)
10cm (4 inches)
or more
30cm (11.8 inches)
or more
(a) Power Swivel
NOT USED
(b) Power Swivel
USED
Wood screw
two places
Wire
24
TABLE OF CONTENTS
A B
4 in. 12 in.
10 cm 30 cm
4 in. 16 in.
10 cm 39 cm
42"
55"
C D
12 in. 12 in.
30 cm 30 cm
15.26 in. 16.46 in.
38.77 cm 41.8 cm
42"
55"
C
D