background image

1.

 

INTRODUCTION

 

1.1

 

General

 

This document is valid as of Dragon PTN Release 3.0DR. 
The 2-OLS interface module (=IFM) is an Optical Low Speed Serial interface module with four 

ports: two Optical Serial ports (=port1, port2) and two E1 ports (=port3, port4). Each optical 

port has two ST connectors: one Rx (=Receive) and one Tx (=Transmit) ST. Each E1 port is an 

RJ-45 connector. This IFM will be used in point-to-point connection and: 

    

converts the incoming serial signal on port1 into E1 on port3 and vice versa; 

   

converts the incoming serial signal on port2 into E1 on port4 and vice versa; 

This IFM can be used in any IFM slot of any node. An IFM slot overview can be found in Ref. 

[3] in Table 1. 

 

 

 

The  E1  links  provide  synchronous  TDM  links  between  two  end  points  that  can  be  used  to 

transport over an external network e.g. SDH. The optical ports are the access ports whereas 

the E1 ports are the SDH interconnection ports. At the destination side, the 2-OLS receives 

the  E1  traffic  and  converts  it  back  to  an  optical  low  speed  serial  signal  towards  the  end 

application. 
In  HiProvision  (=Dragon  PTN  Management),  an  'Optical  Low  Speed  Serial'  service  can  be 

configured  between  two  optical  ports,  each  port  located  in  a  different  node.  This  service 

bundles  together  32  TDM  (Time  Division  Multiplex)  connections  resulting  in  a  total 

bandwidth of 2.048 Mbps. The E1 side can slave its clock for example to the E1 clock from 

the external network. 

NOTE:    

HiProvision can be configured redundantly. 

 

 

Figure 1 2-OLS - SDH Example

 

HiProvision 

Dragon 

PTN Node 

2-OLS

 

IFM 

CSM

 

Optical Serial 

Fiber Links 

Dragon PTN MPLS-TP

 

Network

 

Optical Serial 

Fiber Links 

External Network

 

Example: SDH

 

Teleprotection1 

External E1 Links 

External E1 Links 

Teleprotection2 

'Optical Low Speed Serial' Service

 

CAUTION: This IFM is only a convertor module that needs to be powered via the 

node. It will not have backplane or Dragon PTN network access. The MPLS-TP Drag- 

on PTN network is not required (or optional) for this IFM to operate.

 

Interface Module PTN-2-OLS with E1/PTN-2-OLS with T 

Release 01 02/2018 

 

Summary of Contents for Dragon PTN Series















Reviews: