Hilti UW 10, Operating Instructions Manual

Page: 30 / 71

16
en
4.2 Spare parts for UW10 tool
Spare parts which are unsuitable for the purpose of the
UW10 tool must not be used. Non-observance can result
in loss of warranty coverage. Hilti declines any liability
for damage or loss which could arise from non-obser-
vance of this precaution. (The consecutive numbers are
identical to those in the drawing
).
Consec. no. Item no. Qty. Ordering designation
1 3508 1 Revolving magazine
2 3506 1 Drum assy.
3 6106 1 Trigger assy.
4 3533 1 Casing assy.
5 3536 1 Spring 1
×
23.3
×
63
6 3500 1 Fastener guide
7 3513 1 Axle
8 3501 1 Spall guard
9 3502 1 Flange
10 3548 1 Hex skt screw M6
×
10.5
11 3504 6 Retaining ring
17.5
×
1.6
12 3562 1 Adhesive label
13 3534 6 Barrel 9
×
17
14 3520 1 Magazine cage assy.
15 3523 1 Housing
16 3540 4 Hex skt screw M6
×
12
17 3525 1 Grip frame
18 3524 1 Spring support
19 6151 1 Spring 1.4
×
14.9
×
42.4
Consec. no. Item no. Qty. Ordering designation
20 3526 1 Grip covering
21 3527 1 Cover
22 8622 8 Schnorr washer 8
23 1163 8 Hex. socket screw
M8
×
22
24 3521 2 Lid
25 73450 2 O-ring 17.17
×
1.78
26 0225 2 Spring 0.9
×
6.9
×
24.1
27 3522 1 Sear
28 3535 1 Detent
29 70489 2 Schnorr washer 6
30 72314 2 Hex. socket screw
M6
×
60
31 3514 1 Firing pin guide
32 3529 1 Firing pin U
33 2016908 1 Compression spring
1.6
×
14.7
×
51
34 3528 1 Flange
35 6148 1 Spring 0.4
×
7.4
×
31.8
36 6161 1 Dowel pin 4 M6
×
30
37 6160 1 Spring 1.25
×
13
×
63
38 8773 1 Set screw M8
×
8
39 8771 1 Spring 0.63
×
5.5
×
12
40 8753 1 Detent assy.
41 3551 1 Spring clip assy.
42 3561 1 Adhesive label Hilti
UW10
43 3573 1 Nameplate UW10 CIP
5. Safety precautions
Failure to observe these precautions could result in
personal injury or accident.
1. Never use this tool unless you have received prop-
er instruction on its safe use. For assistance, con-
tact your local Hilti sales representative.
2. Always use this tool in strict accordance with the
operating instructions and always keep them with
the tool.
3. Do not point the tool at yourself or any bystander.
4. Never cock the tool against your hand or other part
of your body. (The cocking force is low).
5. Never leave a loaded tool unattended. Always un -
load the tool before cleaning and servicing, stor-
ing at the end of the day, before works breaks, and
before changing parts.
6. Operator and bystanders must wear appropriate
eye protection and hard hats while the tool is in
use. Wear ear protection when working in con-
fined areas. (A neoprene hood over a diver’s head
is sufficient to protect the ears).
7. Always inspect the tool for proper operation before
using. Do not use a tool that is incomplete or does
not operate properly.
8. Keep the arms flexed when operating the tool ( do
not stiffen arm). If you feel discomfort, discontin-
ue use.
9. Always hold the tool perpendicular to work sur-
face and base material when making fastening.
10. Always use genuine Hilti fasteners, cartridges and
spare parts, or those of equivalent quality.
11. Do not attempt to pry a cartridge from the tool.
Printed: 08.07.2013 | Doc-Nr: PUB / 5071291 / 000 / 01