8
Deutsch
2253586
*2253586*
5.4
Werkzeuge
Die passende Kombination von Einsatzwerkzeug zum Untergrund entnehmen Sie bitte dem Bild.
Erläuterung der Untergründe:
• A: Flachblech
• B: Wellblech
• C: Trapezblech (Profiltiefen bis max. 85 mm)
• D: Trapezblech (Profiltiefen bis max. 162 mm)
Um mit den Werkzeugen SPNRN und SPNRL im Blech bis 1 mm Dicke einen gratfreien Schnitt zu machen,
kann die Matrize P1 verwendet werden. Das geringere Schnittspiel verringert die Gratbildung.
5.5
Werkzeug ausbauen
1. Lösen Sie den Rastbolzen durch sechs Umdrehungen gegen den Uhrzeigersinn.
2. Ziehen Sie das Werkzeug aus dem Gehäuse.
5.6
Werkzeug einbauen
1. Fetten Sie die Stempelführung ein.
2. Hängen Sie den Stempel in die Nut des Stößels ein.
3. Richten Sie die Schneidrichtung nach vorne aus.
4. Stecken Sie das Werkzeug mit der Schneidrichtung nach vorne in das Gehäuse.
5. Positionieren Sie anschließend das Werkzeug in die gewünschte Schneidrichtung.
6. Schrauben Sie den Rastbolzen im Uhrzeigersinn zu und ziehen Sie ihn handfest an.
➥ Zwischen Gehäuse und Matrizenträger darf kein Spalt sein.
5.7
Schneidrichtung einstellen
Bei Bedarf kann die Schneidrichtung nach rechts oder links in 45°-Schritten gedreht werden.
Dadurch können Sie Profilbleche einfacher bearbeiten und den Nibbler für Rechts- oder Linkshandbedienung
einstellen.
1. Lösen Sie den Rastbolzen durch ca. drei Umdrehungen gegen den Uhrzeigersinn, bis keine Rastung
mehr spürbar ist.
2. Ziehen Sie das Werkzeug etwas aus dem Gehäuse und drehen Sie es in die gewünschte Richtung.
➥ Es gibt acht mögliche Rastpositionen.
3. Schieben Sie das Werkzeug in der gewünschten Rastposition zurück in das Gehäuse.
4. Schrauben Sie den Rastbolzen im Uhrzeigersinn zu und ziehen Sie ihn handfest an.
➥ Zwischen Gehäuse und Matrizenträger darf kein Spalt sein.
5.8
Hubzahl einstellen
▶
Stellen Sie die Hubzahl über das Einstellrad für Drehzahl ein.
6
Bedienung
Beachten Sie die Sicherheits- und Warnhinweise in dieser Dokumentation und auf dem Produkt.
6.1
Einschalten
1. Drücken Sie den hinteren Teil des Ein-/Ausschalters.
2. Schieben Sie den Ein-/Ausschalter nach vorne.
➥ Der Motor läuft.
3. Arretieren Sie den Ein-/Ausschalter.
6.2
Schneiden
WARNUNG
Vorsicht
Überlastung des Nibblers durch stumpfe Werkzeuge!
▶
Prüfen Sie regelmäßig die Schneide des Stempels auf Verschleiß. Wechseln Sie den Stempel rechtzeitig
aus, um den Nibbler zu schonen.
Summary of Contents for SPN 6--A22
