![background image](http://html1.mh-extra.com/html/hilti/pd-42/pd-42_operating-instructions-manual_2135814013.webp)
----------
m
----------
m
5.489
m
m
27.317
5.489
m
m
m
12.349
24.634
the tool can be aimed accurately at targets even at great
distance. When the tool is switched on, the laser spot
can be seen in the optical sight. If the laser spot cannot
be seen in the optical sight, either the measurement
has been successfully completed or the laser beam has
switched itself off after the corresponding time interval.
The axis of the optical sight lies parallel to the axis of the
laser beam.
1. Press the “Measure” button to switch the laser beam
on and then aim the tool at the target.
2. Press the “Measure” button or the side “Measure”
button and aim the tool at the target until the laser
spot disappears from the optical sight.
The distance is shown in the display.
6.7 Measuring distances
NOTE
When the spike is folded back in, the measuring reference
is always reset to the rear edge of the tool irrespective of
how far the spike was folded out or to which point on the
tool the measuring reference was previously set.
Distances can be measured from all stationary targets
without a highly reflective surface, i.e. concrete, stone,
wood, plastic, paper, etc. The use of prisms or other
highly reflective targets is not permissible and, if attemp-
ted, may falsify the results.
6.7.1 Measuring distances step by step
NOTE
The range meter measures distances in a very short
time and simultaneously shows various information in the
display.
Switch the tool on by pressing the “On / off” button.
Press the “Measure” button once. The laser beam is
switched on and is visible in the form of a spot on
the target surface. This aiming mode is indicated in the
display by a blinking laser symbol.
Aim at the target. Press the “Measure” button once again
to measure the distance. The result usually appears in
the result line in less than a second and the laser beam
then switches off.
If further measurements are taken, up to three previously
determined distances are shown in the intermediate result
lines, i.e. a total of the last four measured distances are
shown.
en
9
Printed: 08.07.2013 | Doc-Nr: PUB / 5070024 / 000 / 01
Summary of Contents for PD 42
