Adhesive Anchoring Systems
HIT-ICE Adhesive Anchoring System 3.2.5
3.2.5
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en español 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2016 201
3.2.5.1 Product description
3.2.5.2 Material specifications
3.2.5.3 Technical data
3.2.5.4 Installation instructions
3.2.5.5 Ordering information
HIT-ICE cartridge
LEED
®
Credit 4.1-Low Emitting
Materials
The Leadership in Energy and
Environmental Design (LEED
®
) Green
Building Rating system
TM
is the nationally
accepted benchmark for the design,
construction and operation of high
performance green buildings.
HIT-ICE consists of an epoxy acrylate
and hardener. It is formulated for fast
curing and installation in a wide range
of solid base material temperatures.
Designed for colder environmental
installations, HIT-ICE adhesive is a
winter formulation for base material
temperatures down to –10°F (–23°C).
The systems consist of adhesive refill
packs, a mixing nozzle, a HIT dispenser
and either a threaded rod, rebar, HIS-N
internally threaded insert or eyebolts.
HIT-ICE is specifically designed for
fastening into solid base materials
such as concrete or grout-filled block.
Product features of HIT-ICE
• Small edge distance and anchor
spacing allowance
• Mixing tube provides proper
mixing and accurate dispensing
of mixed resin
• Contains no styrene and virtually
odorless
• Cures quickly over a large range of
base material temperatures
• Excellent weathering resistance and
resistance to high temperatures
• High load capacities
Guide specifications
Master format section:
Previous 2004 Format
03250
03 16 00 Concrete
anchors
Related Sections:
03200
03 20 00 Concrete
reinforcing
05050
05 50 00 Metal
fabrications
05120
05 10 00 Structural metal
framing
Injectable adhesive shall be used for
installation of all reinforcing steel dowels
or threaded anchor rods and inserts
into new or existing concrete. Adhesive
shall be furnished in containers which
keep component A and component B
separate. Containers shall be designed
to accept static mixing nozzle which
thoroughly blends component A and
component B and allows injection
directly into drilled hole. Only injection
tools and static mixing nozzles as
recommended by manufacturer shall be
used. Manufacturer’s instructions shall
be followed. Injection adhesive shall be
formulated to include resin and hardener
to provide optimal curing speed as well
as high strength and stiffness. Typical
curing time at 68°F shall be 1 hour for
HIT-ICE. Injection adhesive shall be
HIT-ICE, as furnished by Hilti.
Anchor rods shall be end stamped
to show the grade of steel and overall
rod length. Anchor rods shall be
manufactured to meet the following
requirements:
1.
ISO 898 Class 5.8;
2. ASTM A193,
Grade B7 high strength carbon steel
anchor;
3. AISI 304 or AISI 316 stainless
steel, meeting the requirements of
ASTM F593 condition CW.
Special order length HAS Rods may
vary from standard product.
Nuts and washers shall be furnished
to meet the requirements of the above
anchor rod specifications.
3.2.5.1 Product description
3.2.5.2 Material specifications
Table 1 - Material properties of cured HIT-ICE adhesive
Compressive strength
72 MPa
10,440 psi
Tensile strength
12 MPa
1,740 psi
Water absorption DIN 53495
2.4%
Electrical resistance DIN
/
VDE 0303T3
2x10
11
OHM/cm 5.1x10
11
OHM
/
in.
For material specifications for anchor rods and inserts, please refer to section 3.2.9.
