HiLook PTZ-T5225I-A, Quick Start Manual

Page: 10 / 117

HD-TVI Speed Dome
·
Quick Start Guide
9
Wait one-half hour after switching off before handling parts.
The device with this sticker is intended for installation in a
restricted access location. Access can only be gained by service
persons or by users who have been instructed about the
reasons for the restrictions applied to the location and about
any precautions that shall be taken.
Installation
Install the equipment according to the instructions in this
manual.
To prevent injury, this equipment must be securely attached to
the wall in accordance with the installation instructions.
Be sure that there is enough space to install the device and
accessories.
Make sure that the wall is strong enough to withstand at least
8 times the weight of the device and the mount.
Make sure that the power has been disconnected before you
wire, install, or disassemble the device.
Transportation
Keep the device in original or similar packaging while
transporting it.
Do not drop the product or subject it to physical shock.
Power Supply
The power source should meet limited power source or PS2
requirements according to IEC 60950-1 or IEC 62368-1
standard.
Refer to the device label for the standard power supply. Please
make sure your power supply matches with your device.
Use a power adapter provided by qualified manufacturers. It is
recommended to provide an independent power adapter for
each device as adapter overload may cause over-heating or a
fire hazard.
System Security
Please understand that you have the responsibility to
configure all the passwords and other security settings about
the device, and keep your user name and password.
Maintenance
If the product does not work properly, please contact your
dealer or the nearest service center. We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.
A few device components (e.g., electrolytic capacitor) require
regular replacement. The average lifespan varies, so periodic
checking is recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth to clean the interior and
exterior surfaces. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device
lens is not exposed to the laser beam, or it may burn out.
Do not aim the lens at the sun or any other bright light.
To avoid heat accumulation, good ventilation is required for a
proper operating environment.
DO NOT expose the device to extremely hot, cold, dusty,
corrosive, saline-alkali, or damp environments. For
temperature and humidity requirements, see device
specification.
DO NOT expose the device to high electromagnetic radiation.
Illuminator
Make sure that there is no reflective surface too close to the
device lens. The light from the device may reflect back into the
lens causing reflection.
The beam of the light at the distance of 200 mm is classified as
Risk Group 1 (RG1). Possible hazardous optical radiation
emitted from this product. DO NOT stare at operating light
source. May be harmful to the eyes.
If appropriate shielding or eye protection is not available, turn
on the light only at a safe distance or in the area that is not
directly exposed to the light when installing or maintaining the
device.
Emergency
If smoke, odor, or noise arises from the device, immediately
turn off the power, unplug the power cable, and contact the
service center.
Time Synchronization
Set up device time manually for the first time access if the
local time is not synchronized with that of the network. Visit
the device via web browser/client software and go to time
settings interface.
Cable Description (Page 2
– A)
Notes:
The cables vary depending on different camera models.
1. Power Supply
2. Video Output
3. RS-485 Cable
4. Alarm Cable
DIP Switch and Installation (Page 2
– B)
Table 1-1 Component Description
No. Accessory No. Accessory
A Back Box H Notch
B Sticker I Toggle
C Lower Dome J Bolt
D Protective Foam K Lens Cover
E Lock Screw L Spring
F Ceiling M Lock Clip
G Arrow Label
1. Mini Speed Dome
I. Dip Switch
Table 1-2 Switch Functions
Switch No. Function
1 to 2 (SW2) Set the terminal resistor
1 to 5 (SW1) Set the address for the speed dome
6 to 7 (SW1) Set the baud rate for the speed dome
8 (SW1) Set the protocol for the speed dome
9 to 10 (SW1)
Set the video output mode for the
speed dome
The No.1 to No.5 DIP switches are for setting the address of
speed dome, with value ON=1, 2, 3, 4, 5 standing respectively
for 1, 2, 4, 8, 16, and OFF=0.
Table 1-3 Set Dome Address
Switch
Dome Address
1 2 3 4 5
0 OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF
2 OFF ON OFF OFF OFF
3 ON ON OFF OFF OFF
4 OFF OFF ON OFF OFF
… … … … … …
31 ON ON ON ON ON
Table 1-4 Set Baudrate
Switch
Baud rate
6 7
2400 OFF OFF
4800 ON OFF
9600 OFF ON
19200 ON ON
Table 1-5 Set Protocol
Switch
Protocol
8
Self-adaptive to
private protocol OFF
MAN_AD ON
Table 1-6 Set Video Output
Switch
Video Output
9 10
TVI OFF OFF
AHD ON OFF
CVI OFF ON
CVBS ON ON
The two individual DIP switches, No.1 and No.2, are
used for turning on/off the 120 Ω terminal resistor.
Table 1-7 Set Terminal Resistor
Switch No. 1 2
Turn on the Resistor ON ON
Turn off the Resistor OFF OFF