Hillyard TRIDENT T26 SC PLUS, Use And Maintenance Manual

Page: 23 / 28

To clean the recovery tank filters (with the optional tank cleaning kit), proceed as follows:
1. Take the machine to the maintenance area.
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
2. Release the tank cleaning accessory (1) (at the back of the machine) from the retainers ( Fig.1 ).
3. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (2) on the back of
the machine ( Fig.2 ).
CAUTION : when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
NB : before activating the optional tank cleaning kit, check the level indicator (3) to see how
much solution there is in the recovery tank (
Fig.3
).
4. Activate the solution jet by pressing the lever in the tank cleaning accessory. Make sure the jet is
pointing into the tank before pressing the lever.
NB : to adjust the solution jet from the tank cleaning accessory, turn the knob (4) on the
accessory itself ( Fig.4 ).
NB : to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob (5)
on the accessory itself ( Fig.5 ).
NB : to stop the solution jet,
use the lever (69) on the tank cleaning accessory ( Fig.6 ).
5. Grip the handle (7) on the left-hand side of the recovery tank ( Fig.7 ) and turn the tank cover as
far as it will go, until it reaches the maintenance position.
6. Remove the dirty water basket/filter (8) from the support ( Fig.8 ).
7. Remove the basket cover (9) from the basket/filter (8) (
Fig.9
).
8. Clean the basket/filter and basket cover under the jet of the tank cleaning accessory.
NB : use a spatula or brush to eliminate any dirt that is particularly difficult to remove.
9. Use a cloth to dry the basket/filter and basket cover, and place them back inside the recovery
tank.
10. Remove the filter protection cup (10), turning it in the direction of the arrow ( Fig.10 ).
11. Remove the vacuum motor filter (11), taking care not to lose the support tie (12) inside the
recovery tank ( Fig.11 ).
12. Rinse the cup and filter thoroughly under the jet of the tank cleaning accessory.
NB : use a spatula to eliminate any dirt that is particularly difficult to remove.
13. Repeat the operations in reverse order to refit everything.
CLEANING THE RECOVERY TANK
To clean the recovery tank (without the optional tank cleaning kit), proceed as follows:
1. Make sure the machine is in a safe condition (see “ MACHINE SAFETY MEASURES ”).
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
2. With the recovery tank empty, grip the handle (1) on the left-hand side of the tank ( Fig.1 ) and
turn the tank cover as far as it will go, until it reaches the maintenance position.
3. Rinse the inside of the recovery tank with a jet of water. If necessary, use a spatula to remove
any sludge that may have accumulated at the bottom of the tank.
4. Repeat the operations in reverse order to reassemble all the parts.
To clean the recovery tank (with the optional tank cleaning kit), proceed as follows:
1. Take the machine to the maintenance area.
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
2. Release the recovery tank drainage tube (1) (at the back of the machine) from the retainers
( Fig.1 ).
3. Bend the end of the drainage tube in order to create a choke and prevent the content from
coming out ( Fig.2 ), then position the tube on the discharge surface, unscrew the cap, and
gradually release the tube.
NB : the place designated for this operation must comply with current environmental protection
regulations.
4. With the recovery tank empty, grip the handle (2) on the left-hand side of the recovery tank
( Fig.3 ) and turn the tank cover as far as it will go, until it reaches the maintenance position.
5. Release the tank cleaning accessory (3) (at the back of the machine) from the retainers ( Fig.4 ).
6. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (4) on the back of
the machine ( Fig.5 ).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
NB
: before activating the optional tank cleaning kit, check the level indicator (5) to see how
much solution there is in the recovery tank ( Fig.6 ).
7. Activate the solution jet by pressing the lever in the tank cleaning accessory. Make sure the jet is
pointing into the tank before pressing the lever.
NB : to adjust the solution jet from the tank cleaning accessory, turn the knob (6) on the
accessory itself ( Fig.7 ).
NB : to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob (7)
on the accessory itself ( Fig.8 ).
NB : to stop the solution jet,
use the lever (8) on the tank cleaning accessory ( Fig.9 ).
23
11
11
12
10
10
8 9 7
7
8
8
9
4 5 6
4 5 6
2 3
2 3
1
1
1
1
1
1
3
2
2
4
3
5 6
4 5
7
6
8 9
7 8