Hillstone SG-6000-G2110 Installation Manual Download Page 45

Page: 45 / 50

Hillstone SG-6000 Series Firewall Appliance Installation Manual

Chapter 5 Hardware Maintenance and Replacement

Introduction

This chapter explains how to install and remove the power supply module, the expansion
module and the fan tray.

Installing and Removing the Power Supply Module

This section describes how to install and remove the power supply module of
SG-6000-X5100, SG-6000-G6100, SG-6000-G5150 and SG-6000-G3150.

Installing and Removing the X5100/G6100 Power Supply Module

To install a power supply module to SG-6000-X5100 or SG-6000-G6100:

Ensure that the power supply module to be used is not connected to any power
source.

Face the back panel of the appliance.

If the power supply slot is covered by blank plate, remove the plate first (unscrew
the screws on the blank plate and take it down). Skip this step if the slot is not
covered.

Slide the power supply module all the way into the slot cage until you feel resistant.

Tighten the screws on the flatplate.

Figure 5-1: Installing Power Supply Module of SG-6000-X5100/G6100

To remove the power supply module:

Make sure the power supply module to be used is not connected to any supply
source.

- 38 -

Summary of Contents for SG-6000-G2110



















































Search results

Summary of Contents for SG-6000-G2110

Reviews:

Related manuals for SG-6000-G2110

Brands by name

Popular brands

Hillstone SG-6000-G2110, Installation Manual

Search results

Summary of Contents for SG-6000-G2110

Reviews:

Related manuals for SG-6000-G2110

Brands by name

Popular brands