Service Manual Viking™M mobile lift • 3EN370401 Rev. 19
13
www.hill-rom.com
l
www.liko.com
Customers FAQ:
- The liftarms up/down function or base width in/out function doesn´t work?
a) Change position on actuator and base motor cables.
b) Perform step 2 and see if fault is on output channel or motors.
- The control panel function´s on controlbox is ok, but the hand control has no function?
a) Check to ensure that battery contact plates in the hand control are not defective or broken.
- There´s no charging function?
a) Verify contact between control box and battery. Perform step 4.
b) Check charging function. Perform step 5.
Note!
Begin with Simple trouble shooting from Service manual for the actual
product. If problem remains continue as described below.
Tools Required
Multimeter
1
2
3
2
1
2
3
1
3
green, LED
yellow, LED
5
4
1.
Make sure that:
- the emergency stop 1 is not activated.
- the battery is assembled correctly.
- the charging cable is not connected to mains.
2.
Check operation panel function´s for actuator and base motor
Push control buttons on operation panel 2 at control box
- If both actuator and base motor functions response, continue to step 5.
- If no function, continue to step 3.
- If only one of either the actuator or base motor function response:
change position on actuator and base motor cables then check control
function of operation panel, to see if fault is on output channels or the
motors. If control box function is ok! Continue to step 5.
If control box is faulty.
Replace the control box.
3.
Check battery capacity
3a) Push in the battery capacity button 3 :
- If any of the three LED´s on the battery start´s the battery is OK, continue
to step 4.
- If not, continue to step 3b.
3b)
Measure battery voltage: release battery, 4 measure on contact 1 and 3:
- If voltage over 0V the battery is ok! Continue to step 4.
4.
Verify contact between control box and battery
.
4a)
Remove the battery and wait for green LED to turn off.
4b)
Put back the battery and see if green LED start automatically.
- If green LED starts, battery contact is ok!
- If not, try to ensure that the battery´s contact plates are not defective
or broken and try to bend them out carefully, then repeat step 4.
- If still no contact, continue to step 5.
5.
Check charging function
5a)
Connect the charging cable to mains
- If charging starts within 1 minute, charge and then continue to step 6.
- If charging doesn´t start, continue to step 5b.
5b)
Measure output voltage on the control box 5 on contact 1 and 3.
- If voltage is 3-4V
DC
charging is OK!
Replace the battery
, continue to step 6.
- If voltage is 0V
DC
when the charging cable is connected to mains the control
box needs to be replaced!
Replace the control box
.
6.
Charge the battery until green LED is flashing, on the battery.
- Check that all function´s on the control box is ok!
If not ,
Replace control box
.
Check point:
Trouble shooting
Control Unit CBL
4.0
Spare Parts List
67
www.hill-rom.com
l
www.liko.com
Product No. 2040015
(
S/N 7 500 401 - 7 600 500)
2040035
(
S/N 9 200 001 -
9 300 000)
Fits all models of Viking™ M:
Service Tools
Liko™ Service System
Liko™ Diagnostic System
Spare Parts Positions Viking™ M
mobile lift
307
22 23 24 28
160 263
196
418
292
55
139
19
268
266
328
285
460
410
284
159 485 486
199
439
548
331
197 308
461
490
264 311
348 349
20
353
307
511
354
352
351
333
418
293
422
350
336
334
199
266
328
285
284
159 485 486
460
410
439
347
331
293
308
461
490
264 311
Product No. 2040005
(
S/N 7 100 101 - 7 200 200)
2040005
Viking M
(Discontinued 2013)
2040015
Viking M (CBL control box)
(Discontinued 2016)
2040035
Viking M (CBL control box and cable hand control)
(Discontinued 2016)
PROD. NO.
PRODUCT
