HIKVISION UD03451B User Manual Download Page 49

Page: 49 / 52

Smart Camera User Manual

Chapter 4

Troubleshooting

4.1

Indicator Introduce

There are five LED indicators in the camera, power indicator, network linkage

indicator, network transmission indicator, user indicator 1, and user indicator 2, shown

as the figure below.

PWR

LNK

ACT

Figure 4. 1

Camera Indicator

Table 4. 1

LED Indicator Description

Name

Description

PWR

Power indicator

LNK

Network linkage indicator

ACT

Network transmission indicator

User indicator 1

User indicator 2

4.2

Indicator Status Definition

Table 4. 2

LED Indicator Status

LED Status

Definition

Steady On

The LED indicator keeps lights on all the time

Unlit

The LED indicator keeps unlit all the time

Fast Flicker

The LED indicator flickers every 200 ms to 300 ms

Slow Flicker

The LED indicator flickers every 1000 ms.

Extreme Slow Flicker

The LED indicator flickers every 2000 ms.

Summary of Contents for UD03451B





















































Search results

Summary of Contents for UD03451B

Reviews:

Brands by name

Popular brands

HIKVISION UD03451B, User Manual

Search results

Summary of Contents for UD03451B

Reviews:

Brands by name

Popular brands