HIKVISION U1T Series User Manual Download Page 3

 

Safety Instruction 
These instructions are intended to ensure that user can 

use the product correctly to avoid danger or property 

loss.   
The precaution measure is divided into “Warnings” and 

“Cautions”. 
Warnings: Serious injury or death may occur if any of the 

warnings are neglected. 

Cautions: Injury or equipment damage may occur if any 

of the cautions are neglected. 

  Warnings 

 

In the use of the device, you must be in strict 
compliance with the electrical safety regulations of the 

nation and region. 

 

Input voltage should meet both the SELV (Safety Extra 
Low Voltage) and the Limited Power Source with 12 

VDC according to the IEC60950-1 standard. Refer to 

technical specifications for detailed information. 

 

Do not connect multiple devices to one power adapter 

to avoid over-heating or a fire hazard caused by 
overload. 

 

Make sure that the plug is firmly connected to the 

power socket. 

 

Make sure that the device is firmly fixed if wall 

mounting or ceiling mounting is adopted. 

 

If smoke, odor or noise rise from the device, turn off 
the power at once and unplug the power cord, and 
then contact the service center.   

 

Never attempt to disassemble the camera by 
unprofessional personal. 

  Cautions 

 

Do not drop the camera or subject it to physical shock. 

 

Do not place the camera in extremely hot, cold (the 
operating temperature shall be -40°C to 60°C), dusty or 

damp locations, and do not expose it to high 
electromagnetic radiation. 

 

Do not touch senor modules with fingers.   

 

If cleaning is necessary, use clean cloth with a bit of 
ethanol and wipe it gently.   

 

Do not aim the camera at the sun or extra bright places.   

 

The sensor may be burned out by a laser beam, so 

when any laser equipment is in using, make sure that 
the surface of sensor will not be exposed to the laser 

beam. 

 

Do not expose the device to high electromagnetic 
radiation or extremely hot, cold, dusty or damp 

environment.   

 

To avoid heat accumulation, good ventilation is 
required for the operating environment.   

 

Keep the camera away from liquid while in use for non-
water-proof device. 

 

 

Warnings Follow 
these safeguards to 
prevent serious injury 
or death. 

Cautions Follow these 
precautions to prevent 
potential injury or 
material damage.   

Summary of Contents for U1T Series

















Reviews: