background image

 

Network Traffic Speed Dome

·

Quick Start Guide

 

 

iv 

Regulatory Information 

FCC Information 
Please take attention that changes or modification not expressly approved by the party 
responsible for compliance could void the user’s authority to operate the equipment. 
FCC compliance: This equipment has been tested and found to comply with the limits 
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference when the 
equipment is operated in a commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with 
the instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful interference 
in which case the user will be required to correct the interference at his own expense. 
FCC Conditions 
This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: 
1. This device may not cause harmful interference. 
2. This device must accept any interference received, including interference that may 
cause undesired operation. 
EU Conformity Statement 

This product and - if applicable - the supplied accessories too are marked 
with "CE" and comply therefore with the applicable harmonized European 
standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 

2011/65/EU. 

2012/19/EU (WEEE directive): Products marked with this symbol cannot be 
disposed of as unsorted municipal waste in the European Union. For proper 
recycling, return this product to your local supplier upon the purchase of 
equivalent new equipment, or dispose of it at designated collection points. 

For more information see: www.recyclethis.info.

 

2006/66/EC (battery directive): This product contains a battery that cannot 
be disposed of as unsorted municipal waste in the European Union. See the 
product documentation for specific battery information. The battery is 
marked with this symbol, which may include lettering to indicate cadmium 

(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier 
or to a designated collection point. For more information see

www.recyclethis.info

Industry Canada ICES-003 Compliance 
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. 
Waring: 
This is a class A product. In a domestic environment this product may cause radio 
inter-ference in which case the user may be required to take adequate measures. 
 

Summary of Contents for iDS-2VS435-F840-EY

























Reviews: