background image

DS-TMG033 Barrier Gate Radar User Manual

 

 

Symbol Conventions 

The symbols that may be found in this document are defined as follows. 

Symbol   

Description   

 

Provides additional information to emphasize or supplement important 
points of the main text. 

 

Indicates a potentially hazardous situation, which if not avoided, could 
result in equipment damage, data loss, performance degradation, or 
unexpected results. 

 

Indicates a hazard with a high level of risk, which if not avoided, will result 
in death or serious injury. 

Safety Instructions

 

 

Proper configuration of all passwords and other security settings is the responsibility of the 
installer and/or end-user. 

 

In the use of the product, you must be in strict compliance with the electrical safety 
regulations of the nation and region. Please refer to technical specifications for detailed 
information. 

 

Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power 
Source according to the IEC60950-1 standard. Please refer to technical specifications for 
detailed information. 

 

Do not connect several devices to one power adapter as adapter overload may cause 
over-heating or a fire hazard. 

 

Please make sure that the plug is firmly connected to the power socket.     

 

If smoke, odor or noise rise from the device, turn off the power at once and unplug the power 
cable, and then please contact the service center.   

Preventive and Cautionary Tips

 

Before connecting and operating your device, please be advised of the following tips: 

 

Ensure unit is installed in a well-ventilated, dust-free environment. 

 

Unit is designed for indoor use only. 

 

Keep all liquids away from the device. 

 

Ensure environmental conditions meet factory specifications. 

 

Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of 
dropping it may cause damage to the sensitive electronics within the unit. 

Summary of Contents for DS-TMG033





















Reviews: