background image

DS-TMG033 Barrier Gate Radar User Manual

 

 

User Manual 

COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd.   

ALL RIGHTS RESERVED. 

Any and all information, including, among others, wordings, pictures, graphs are the properties of 
Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be 
“Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, 
changed, translated, or distributed, partially or wholly, by any means, without the prior written 
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, 
guarantees or representations, express or implied, regarding to the Manual. 

About this Manual   

This Manual is applicable to DS-TMG033 Barrier Gate Radar. 

The Manual includes instructions for using and managing the product. Pictures, charts, images and 
all other information hereinafter are for description and explanation only. The information 
contained in the Manual is subject to change, without notice, due to firmware updates or other 
reasons. Please find the latest version in the company website 
(

http://overseas.hikvision.com/en/

).   

Please use this user manual under the guidance of professionals. 

Trademarks Acknowledgement 

  and other Hikvision’s trademarks and logos are the properties of Hikvision in various 

jurisdictions. Other trademarks and logos mentioned below are the properties of their respective 
owners. 

Legal Disclaimer 

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS 
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, 
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, 
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND 
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, 
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR 
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, 
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE 
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGES. 

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY 
AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL 
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER 
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL 
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.   

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR 
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS 
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS 
USED WITH ILLEGITIMATE PURPOSES.   

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER 
PREVAILS. 

Summary of Contents for DS-TMG033





















Reviews: