manualshive.com logo in svg

HIKVISION DS-K3Y411 Series, Quick Start Manual

Share
Download
HIKVISION DS-K3Y411 Series Quick Start Manual Download Page 33

Terminal Name

Description

Lane Controller Board

Connect sub lane controller board

5 V

Reserved

IR Adaptor

Connects IR adaptor

UART 5

Note

External card reader is

recommended to access.

Red 12 V: connects 12 VDC power supply terminal
Yellow 485E/232E+: card reader RS-485E+/RS-232E+ access

terminal
Blue 485E/232E-: card reader RS-485E-/RS-232E- access terminal
Black GND: grounding

UART 6

Note

External face recognition

terminal is recommended to

access.

Red 12 V: connects 12 VDC power supply terminal
Yellow 485F/232F+: card reader RS-485F+/RS-232F+ access

terminal
Blue 485F/232F-: card reader RS-485F-/RS-232F- access terminal
Black GND: grounding

4.5.5 Access Control Board Terminal Description

Access control board is mainly used for authority identification, external device accessing, and

communication with the upper platform and lane controller.

DS-K3Y411X Series Flap Barrier Quick Start Guide

21

Summary of Contents for DS-K3Y411 Series































































Reviews:

No comments

Brands by name

Popular brands

Load more brands