HIKVISION DS-K3G501S Series Quick Start Manual Download | Manualshive

Page: 18 / 47

background image

Figure 3-2 Dimension

1. Prepare for the installation tools, check the components, and prepare for the installation base.
2. Drill holes on the ground according to the installation holes on the pedestals and insert the

expansion sleeves.

3. According to the entrance and exit marks on the pedestals, move the pedestals to the

corresponded positions.

Note

Make sure the installation holes on the pedestals and the base are aligned with each other.

4. Seal the bottom of the turnstile to avoid water from entering.

Note

Make sure the installation holes on the pedestals and the base are aligned with each other.

5. Secure the pedestals with expansion bolts.

Note

●

Do not immerse the pedestal in the water. In special circumstances, the immersed height

should be no more than 690 mm.

●

The installation footprint is as follows:

DS-K3G501SX Series Tripod Turnstile Quick Start Guide

7

«
...
16
17
18
19
20
...
»

Summary of Contents for DS-K3G501S Series
















































Reviews:

No comments

Related manuals for DS-K3G501S Series

Brand: CAME Pages: 80

Brand: CAME Pages: 80

Brand: Turnstiles Pages: 7

Brand: Turnstiles Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands