background image

Secure Door Control Unit                                                  Hikvision.com 

iii 

2006/66/EC (battery directive): This product contains a battery 
that cannot be disposed of as unsorted municipal waste in the 
European Union. See the product documentation for specific 
battery information. The battery is marked with this symbol, 
which may include lettering to indicate cadmium (Cd), lead 
(Pb), or mercury (Hg). For proper recycling, return the battery 

to your supplier or to a designated collection point. For more information see: 

www.recyclethis.info

 
Industry Canada ICES-003 Compliance
 
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. 
Safety Instruction 
These instructions are intended to ensure that user can use the product correctly 
to avoid danger or property loss. 
The precaution measure is divided into Warnings and Cautions
Warnings: Neglecting any of the warnings may cause serious injury or death. 
Cautions: Neglecting any of the cautions may cause injury or equipment damage. 

  Warnings 

 

All the electronic operation should be strictly compliance with the electrical 

safety regulations, fire prevention regulations and other related regulations in 
your local region. 

 

Please use the power adapter, which is provided by normal company. The 

power consumption cannot be less than the required value. 

 

Do not connect several devices to one power adapter as adapter overload may 

cause over-heat or fire hazard. 

 

Please make sure that the power has been disconnected before you wire, 

install or dismantle the device. 

 

When the product is installed on wall or ceiling, the device shall be firmly 

fixed.   

 

If smoke, odors or noise rise from the device, turn off the power at once and 

unplug the power cable, and then please contact the service center. 

 

 

Warnings Follow these safeguards 

to prevent serious injury or death. 

Cautions Follow these precautions to 

prevent potential injury or material 

damage. 

Summary of Contents for DS-K2M060





















Reviews: