HIKVISION DS-7204HI-S Series User Manual Download Page 11

Page: 11 / 88

Stop using IR remote control

When DVR controlled by IR remote control, press [DEV] key again, then the IR

remote control can not control this DVR.

Switch the DVR off

When IR remote control is working, press [POWER] key for several seconds,

then the power off prompt will pop up, press [Confirm] and switch off the power on
the rear panel manually.

When IR remote control can not work normally



Check batteries poles.



Check the remaining charge in the batteries.



Check IR remote control sensor is masked.



Please change another IR remote control and try again. If the problem still exists,
please contact administrator.

3.3 Menu Description

3.3.1 Menu Items

Table 3.3 First Glance at menu

Menu Name

Function

Menu Name

Function

Display

Device ID

Enable password

Screen saver

Video standard

Enable scale

Brightness

Menu transparency

VGA resolution

Date/Time

Preview

Camera

Select camera

Name

Color

Date OSD

Motion Det. Level

Advanced Settings

Copy to camera

Recording

If HD Full

Select camera

Stream type

Resolution

Frame rate

Bit rate

Enable Rec

Network

Port

Mask

Gateway

Http Port

Advanced Settings

PPPoE

Summary of Contents for DS-7204HI-S Series

























































































Search results

Summary of Contents for DS-7204HI-S Series

Reviews:

Related manuals for DS-7204HI-S Series

Brands by name

Popular brands

HIKVISION DS-7204HI-S Series, User Manual

Search results

Summary of Contents for DS-7204HI-S Series

Reviews:

Related manuals for DS-7204HI-S Series

Brands by name

Popular brands