HIKVISION AE-MH0408 User Manual Download Page 64

Page: 64 / 79

Mobile Network Video Recorder User Manual

Upgrade the System

Purpose:

The device can be upgraded either through local USB flash disk or remote FTP server.

Before you start:



Connect the USB device that contains the upgrade firmware.



The upgrade firmware should be stored in the root directory of the USB device.

Go to Menu > Maintenance > Upgrade.

Select Upgrade Type as USB Upgrade.

Upgrade

Click Upgrade to start upgrading and reboot the device to activate the new settings.

Before you start:

Ensure the network connection of the PC (running FTP server) and the device is valid and
correct. Run the FTP server on the PC and copy the firmware into the corresponding
directory of your PC.

Refer to the user manual of the FTP server to set the FTP server on your PC and put the
firmware file into the directory as required.

Summary of Contents for AE-MH0408
















































































Search results

Summary of Contents for AE-MH0408

Reviews:

Related manuals for AE-MH0408

Brands by name

Popular brands

HIKVISION AE-MH0408, User Manual

Search results

Summary of Contents for AE-MH0408

Reviews:

Related manuals for AE-MH0408

Brands by name

Popular brands