4
English
○
Never pull the switch trigger while the tip of the saw
blade tip is pressed against the material. If you do so, the
blade can easily be damaged when it collides with the
material.
○
Make absolutely sure that you cut slowly while holding
the body
fi
rmly. If you apply any unreasonable force to
the saw blade during the cutting operation, the blade can
easily be damaged.
12. Cut o
ff
guide for cutting pipe (optional accessory)
Please refer to the cut o
ff
guide user’s manual for details
on how to use it correctly.
SYMBOLS
WARNING
The following show symbols used for the machine. Be
sure that you understand their meaning before use.
CR13V2: Reciprocating Saw
Read all safety warnings and all instructions.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Switching ON
Switching OFF
Stroke
Disconnect mains plug from electrical outlet
Class
II
tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○
Blade (No. 341) .............................................................1
○
Case .............................................................................1
○
Hexagonal bar wrench ..................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○
Cutting pipe and angle steel.
○
Cutting various lumbers.
○
Cutting mild steel plates, aluminum plates, and copper
plates.
○
Cutting synthetic resins, such as phenol resin and vinyl
chloride.
For details refer to the section entitled “SELECTION OF
BLADES”.
SPECIFICATIONS
Voltage (by areas) *
(110 V, 115 V, 120 V, 127 V,
220 V, 230 V, 240 V)
Power Input
1010 W *
Capacity
Mild Steel Pipe
O.D. 130 mm
Vinyl Chloride
Pipe
O.D. 130 mm
Wood
Depth 300 mm
Mild Steel Plate
Thickness 19 mm
No-Load Speed
0 – 2800 min
–1
Stroke
29 mm
Weight (without cord)
3.3 kg
* Be sure to check the nameplate on product as it is subject
to change by areas.
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci
fi
cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Figure
Page
Mounting the blade
1
130
Taking the broken blade out
2
130
Maintenance and inspection of
saw blade mount
3
130
Blade hole
4
130
Adjusting the base
5
131
Switch Operation
6
131
Selection of saw blade length
7
131
Fastening work piece
fi
rmly
8
131
Plunge cutting
9
132
Plunge cutting with the saw blade
installed in reverse
10
132
Replacing carbon brushes
11
132
Selecting accessories
―
133
Refer to
Table 1, 2, 3
and
4
for use of the blades.
SELECTION OF BLADES
To ensure maximum operating e
ffi
ciency and results, it is
very important to select the appropriate blade best suited to
the type and thickness of the material to be cut.
NOTE
Dimensions of the workpiece mentioned in the table
represent the dimensions when the mounting position of
the base is set nearest to the body of the reciprocating
saw. Caution must be exercised since dimensions of the
workpiece will become smaller if the base is mounted far
away from the body of the reciprocating saw.
1. Selection of HCS blades
The blade number of HCS blades in
Table 1
is engraved
in the vicinity of the mounting position of each blade.
Select appropriate blades by referring to
Tables 1
and
4
below.
0000Book̲CR13V2.indb 4
0000Book̲CR13V2.indb 4
2017/12/04 9:43:04
2017/12/04 9:43:04
