16
(2) Regarding the temperatures and charging time of the rechargeable battery
The temperatures and charging time will become as shown in
Table 2.
Table 2
Charger
UC18YSL3
Battery
Type of battery
Li-ion
Temperatures at which the
battery can be recharged
0°C – 50°C
Charging voltage
V
14.4
18
Charging time,
approx. (At 20°C)
BSL14xx series
BSL18xx series
Multi volt
series
(4 cells)
(8 cells)
(5 cells)
(10 cells)
(10 cells)
min.
BSL1415S : 15
BSL1415 : 15
BSL1415X : 15
BSL1420 : 20
BSL1425 : 25
BSL1430C : 30
BSL1430 : 20
BSL1440 : 26
BSL1450 : 32
BSL1460 : 38
BSL1815S : 15
BSL1815 : 15
BSL1815X : 15
BSL1820 : 20
BSL1825 : 25
BSL1830C : 30
BSL1830 : 20
BSL1840 : 26
BSL1850 : 32
BSL1860 : 38
BSL36A18 : 32
BSL36B18 : 52
USB
Charging voltage
V
5
Charging current
A
2
NOTE
The recharging time may vary according to the ambient temperature and power source voltage.
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger
fi
rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the
fi
rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2 – 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○
If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (o
ff
for
0.3 seconds). In such a case,
fi
rst let the battery cool,
then start charging.
○
When the charge indicator lamp
fl
ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○
Since the built-in micro computer takes about
3 seconds to con
fi
rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Figure
Page
Removing and inserting the battery
2
2
Charging
3
2
Changing blades
4
3
Adjusting the blade operating speed
*1
5
3
Adjusting the orbital operation
6
3
Splinter guard
7
4
Sub base
*2
(sold separately)
8
4
Chip cover
9
4
Housing the hexagonal bar wrench
10
4
Switch operation
*3
11
5
How to use the LED light
*4
12
5
Remaining battery indicator
13
6
Mounting the guide (sold separately)
14
6
Rectilinear cutting
15
6
Cutting a circle or a circular arc
16
6
Cutting metallic materials
17
7
0000Book̲CJ36DA̲AUST.indb 16
0000Book̲CJ36DA̲AUST.indb 16
2019/08/05 5:47:13
2019/08/05 5:47:13
