HIK VISION 23 Series Quick Start Manual Download Page 39

Page: 39 / 55

Camera

Switch/Router

Align the snap and notch.

i. Insert

⑤

into

④

ii. Secure

⑥

with

④

Network Turret Camera

Quick Start Guide

Place the O-type gasket

②

onto the end of the camera’s

network interface socket

①

Insert the network plug

③

into the camera’s

network interface

socket

①

Insert the water-proof rubber gasket

⑤

into the waterproof

endcap

④

, and secure lock nut

⑥

with the water-proof

endcap

④

Align the snap on the water-proof endcap

④

with the notch on

the camera’s network interface socket

①,

and then secure the

water-proof endcap

④

to the camera’s network interface

socket

①

to finish installation.

Figure 2-38 Water-proof Accessory Installation

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Summary of Contents for 23 Series
























































Search results

Summary of Contents for 23 Series

Reviews:

Related manuals for 23 Series

Brands by name

Popular brands

HIK VISION 23 Series, Quick Start Manual

Search results

Summary of Contents for 23 Series

Reviews:

Related manuals for 23 Series

Brands by name

Popular brands