High End Systems SolaFrame 3000 User Manual Download Page 16 | Manualshive

Page: 16 / 32

background image

12

SolaFrame 3000

Connect DMX Cables to Fixture

The following instructions are guidelines for connecting DMX to your fixture. Your installation
may vary.

1.

Connect the male XLR connector of a DMX data cable to the DMX Out connector on the
DMX control source.

2.

Connect the female XLR connector of the DMX data cable to the DMX In connector of the
first fixture on the DMX control run.

3.

Continue linking the remaining fixtures connecting a cable from the DMX Out connector
of each fixture to the DMX In connector of the next fixture on the control run.

«
...
14
15
16
17
18
...
»

Summary of Contents for SolaFrame 3000

































Reviews:

No comments

Related manuals for SolaFrame 3000

Brand: Makita Pages: 10

Brand: CAMAG Pages: 40

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: ParaBody Pages: 3

Brand: Hach Pages: 52

Brand: hager Pages: 2

Brand: Mangar International Pages: 8

Brand: Malvern Instruments Pages: 30

Brand: zarges Pages: 36

Brand: JBSYSTEMS Light Pages: 17

Brand: Waters Pages: 250

Brand: Waters Pages: 141

Brand: GE Pages: 18

Sonorex Super RK 31

Brand: BANDELIN Pages: 21

BTL7-A/E501-M Series

Brand: Balluff Pages: 194

Brand: ABB Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands