background image

Malfunction: 

no function

Reason:

Remedy:

1. The power supply connection of the device is not correct.

Recheck

2. The cables have no mechanical or electrical contact.

Recheck

3. The remote turn-on connection from the headunit to the amplifier is not correct.

Recheck

4. The high level inputs (from the head unit) are not connected correct and AUTO TURN ON is activated.

See page 16 and 21

5. By using the AUTO TURN ON function the button INPUT LEVEL MODE is not in HI position and the button

Set buttons to HI and ON

    AUTO TURN ON not in ON position or the headunit is not equipped with ”High Power” outputs.

See page 16

6. Defective Fuses. In case of replacing the fuses, attend by any means the correct fuse rating.

Replace Fuses

Malfunction: 

no signal on loudspeakers, but power LED lights up

Reason:

Remedy:

1. The connection of the speakers or the RCA audio cables is not correct.

Recheck

2. The speaker cables or the RCA audio cables are defective.

Replace cables

3. The loudspeakers are defective.

Replace speakers

4. High pass controller (Subsonic Mode) in LP/BP operation is adjusted to high.

Turn down controller

5. No signal from headunit.

Check headunit settings

Malfunction:

 

one or more channels/controllers are without function / faulty stereo stage

Reason:

Remedy:

1. The balance or  fader controller of the headunit is not in the zero-position.

Turn to zero-position

2. The connection of the speakers is not correct.

Recheck

3. The loudspeakers are defective.

Replace speakers

4. High pass controller in LP/BP operation is adjusted to high.

Turn down controller

Malfunction:

 

distortions on the loudspeaker’s signal

Reason:

 

Remedy:

1. The loudspeakers are overloaded. 

Turn down the level

Turn down the level on the headunit

Switch off loudness on the headunit

Reset bass EQ on the headunit

Malfunction:

 

No bass or stereo sound

Reason:

 

Remedy:

1. Interchange of loudspeaker cable polarity positive (+) and negative (-).

Reconnect

2. The RCA audio cables are loose or defective.

Reconnect or replacing the cables

Malfunction: 

amplifier runs into protection mode (red protection LED lights up)

Reason:

Remedy:

1. Short circuit on the loudspeakers or cables.

Reconnect

2. Overheated by too low speaker impedance.

Choose a higher impedance

Use a new speaker setup

3. Insufficient air circulation by a inappropriate mounting position of the amplifier.

Change the mounting position

Ensure air circulation

4. Overloaded by insufficient power supply (too thin profile section on the power cables).

Use a bigger profile section

Malfunction:

 

hiss or white noise on the loudspeaker’s signal

Reason:

Remedy:

1. The level controllers are turned up.

Turn down the level

2. The treble controller on the headunit is turned up.

Turn down the level on the headunit

3. The speaker cables or the RCA audio cables are defective.

Replacing the cables

4. The hissing is caused by the headunit.

Check the headunit

22

ENG|

TROUBLE SHOOTING

Summary of Contents for Triton II

























Reviews: