21
FUNCTIONAL INSTRUCTIONS
3
16
4
10
5
9
13
11
12
7
8
14
15
6
The
CH1/2 X-OVER
switch selects the required operation mode of the amplifier on Channel 1/2.
HP
: Highpass mode (The higher frequencies will be eliminated. Adjustable by the HP controller).
FULL
: Fullrange mode (All frequencies will be amplified).
The
BASS LEVEL CONTROLLER
port is for the enclosed bass remote controller in LP/BP mode. With this bass remote cont-
roller you are able to adjust the bass level e.g. from the driver’s seat. Please connect only the enclosed bass remote controller
and cable.
The
HP CH1/2
controller (high pass) adjust the cut-off point of the frequency range for Channel 1/2 to below. The cut-off frequen-
cy is continuously adjustable from 50Hz to 4kHz.
The
LP CH5
controller (low pass) adjusts the cut-off point of the frequency range of Channel 5 (Subwoofer Channel) to above.
The cut-off frequency is continuously adjustable from 35 Hz to 150 Hz.
The
LEVEL CH1/2
controller adjust the input sensitivity of the amplifier to align the audio signal of the head unit on Channel 1/2.
The input sensitivity is adjustable from 6 Volts (MIN) and 0.2 Volts (MAX).
The
LEVEL CH3/4
controller adjust the input sensitivity of the amplifier to align the audio signal of the head unit on Channel 3/4.
The input sensitivity is adjustable from 6 Volts (MIN) and 0.2 Volts (MAX).
The
LEVEL CH5
controller adjust the input sensitivity of the amplifier to align the audio signal of the head unit on Channel 5
(Subwoofer Channel). The input sensitivity is adjustable from 6 Volts (MIN) and 0.2 Volts (MAX).
The
SUBSONIC
CH5
controller cuts off the ultra-deep and low inaudible frequencies of the audio signal from the subwoofer
channel. Hence, the subwoofer is not mechanically and electrically overloaded. The cut-off frequency can can be adjusted from
15 and 55 Hz, depending on the size of the subwoofer.
NOTE:
If this controller is set higher than the LP controller no audio is hearable.
The
BASS BOOST CH5
controller adjust the bass boost enhancement continuously from 0dB to +18dB.
The
CH3/4 X-OVER
switch selects the required operation mode of the amplifier on Channel 3/4.
HP:
Highpass mode (The higher frequencies will be eliminated. Adjustable by the HP/BP controller).
FULL:
Fullrange mode (All frequencies will be amplified).
BP:
Bandpass mode (The HP/BP controller cuts the lower and the LP controller the higher frequencies).
The
LP
CH3/4
controller adjusts the cut-off point of the frequency range of Channel 3/4 to above. The cut-off frequency is conti-
nuously adjustable from 150 Hz to 4000 Hz.
POWER/PROTECT
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Attend in this case the chapter TROUBLE SHOOTING.
With the
INPUT MODE
switch you can choose whether you want to drive the amp one pair of RCA cables (position 2CH), with
two pairs of RCA cables (position 4CH) or three pairs of RCA cables (position 5CH).
NOTE:
If you want to use the
AUTO TURN
ON
function the switch must be in 2CH position.
The
HP/BP CH3/4
controller (high pass / band pass) adjusts the cut-off point of the frequency range for Channel 3/4 to below.
The cut-off frequency is continuously adjustable from 50Hz to 250Hz.
Summary of Contents for ARX5005
