Hi-Z Antennas 4-8 PRO Manual Download Page 15 | Manualshive

Page: 15 / 15

background image

15

F connector tightening procedure.

Placing a 7/16” wrench on the chassis connector while holding it tight, place

another 7/16” wrench over the Male connector housing and tighten until snug. Do not over tighten this F connector.
View pictures below.

Hi-Z 4-8PRO UP Manual V1.0

©2011 Hi-Z Antennas™

www.hizantennas.com

«
...
13
14
15

Summary of Contents for 4-8 PRO
















Reviews:

No comments

Related manuals for 4-8 PRO

HyperGain HG2424G

Brand: l-com Pages: 3

Brand: Federal Signal Corporation Pages: 18

Brand: EnGenius Pages: 2

Brand: SELFSAT Pages: 40

Brand: ICPDAS Pages: 8

Brand: GeoMax Pages: 104

WAYFARER 1.2M KA-BAND

Brand: Norsat Pages: 29

WAYFARER 1.0M KU-BAND

Brand: Norsat Pages: 32

Brand: Hy-Gain Pages: 23

Brand: Zenith Pages: 2

Brand: M2 Antenna Systems Pages: 6

Brand: M2 Antenna Systems Pages: 8

Brand: Mohu Pages: 2

Brand: Radio Shack Pages: 7

Brand: Quasonix Pages: 40

Brand: Oricom Pages: 2

Brand: MFJ Pages: 3

Brand: Harris Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands