manualshive.com logo in svg

Hi-Z Antennas 4-8 PRO, Manual

Share
Download
Hi-Z Antennas 4-8 PRO Manual Download Page 11

11

HF RECEIVING

 

SYSTEMS & COMPONENTS

Hi-Z Antennas™ 

Hi-Z Amplifier

 

Hi-Z Amplifier 

The Hi-Z Amplifier was designed to provide amplification and matching between the short verticals and the phase controller in 
the Hi-Z phased array control systems. This amplifier is used on ALL Hi-Z phased array products. The amp is located at the base 
of each short vertical. The connecting wires must be short, in the range or 8-10 inches long. When dressing or routing the wires 
between the vertical and ground rod to the Hi-Z Amps, maintain as much separation between the ground and antenna wires as 
possible. If these wires are to close it will degrade the system performance.

 

The Hi-Z Amp MUST be Weatherproofed!!

Please review our application and technical notes to gain ideas for mounting the Hi-Z amplifiers near the base of the verticals. 
See:

  

http://www.hizantennas.com/hiz_verticals.htm

Features:

•

Relay input (lightning and static protection, when power is off)

•

Easy connections to the base of the vertical and ground 

Hi-Z 4-8PRO UP Manual V1.0

©2011 Hi-Z Antennas™

www.hizantennas.com

Summary of Contents for 4-8 PRO
















Reviews:

No comments

Brands by name

Popular brands

Load more brands