Hi-Vac X-Vac Hydro Excavator X15 Series Operation, Service & Parts Manual Download Page 85

Page: 85 / 87

BODY

POLYTANK INSTALLATION INSTRUCTIONS

(New Style)

Place left rear and right rear water tanks onto tank frame assembly.

Attach hoses and suction tee weldment.

Place left front and right front water tanks onto tank frame assembly.

Attach short and long inter connect hoses between front and rear tanks.

Attach caps on front water tanks.

Install retaining straps.

Note:

For a detailed listing of parts, refer to drawing A385300_T.

Front and Rear Water Tank

Inter Connect Hoses

Hoses

and

Suction Tee Weldment

Front Water Tank Caps

BODY 5

AQUATECH OPERATIONS, SERVICE AND PARTS MANUAL

A Product of Hi-Vac Corporation

Summary of Contents for X-Vac Hydro Excavator X15 Series
























































































Search results

Summary of Contents for X-Vac Hydro Excavator X15 Series

Reviews:

Related manuals for X-Vac Hydro Excavator X15 Series

Brands by name

Popular brands

Hi-Vac X-Vac Hydro Excavator X15 Series, Operation, Service & Parts Manual

Search results

Summary of Contents for X-Vac Hydro Excavator X15 Series

Reviews:

Related manuals for X-Vac Hydro Excavator X15 Series

Brands by name

Popular brands