HF PackerAmp V4 Construction Manual Download Page 35

Page: 35 / 76

HF PACKER

AMP

V4R6

Page 35

•

Note that the coax center goes into the hole on the

right in the L2 position. The shield wire connects to the
hole directly above it.

•

This cable will connect to J2 on the PINET 100-PI

module. Identify the cable as J2.

•

Attach a peal and stick rubber bumper to the top of

C16, a 330uF capacitor.

Attach the Model PI-100 Module

•

Attach the PI-100 Module using two 4-40 x3/16 inch

screws into the Male/Female Jack Screw just added.
The PI-100 Module will extend towards the rear over
the PSU and rest on top of the rubber bumper.

Cable Connections on the Model PI-100 Module

•

Plug in the two RF Cables to J1 and J2.

•

Attach the Power Cable to J4.

The two RF cables at J1 and J2 route with very short
connections from the Amp.

Set the Jumper at the 3-pin header J3 on the PI-
100 Module

•

Install the provided jumper in one of three ways.

•

With no jumper, the maximum RF Drive input is 1W

•

With the jumper in the 2-3 position, max RF Drive is

2.5W

•

With the jumper in the 1-2 position, max RF Drive is



set to 5W for testing procedure of Amp

Summary of Contents for PackerAmp V4













































































Search results

Summary of Contents for PackerAmp V4

Reviews:

Related manuals for PackerAmp V4

Brands by name

Popular brands

HF PackerAmp V4, Construction Manual

Search results

Summary of Contents for PackerAmp V4

Reviews:

Related manuals for PackerAmp V4

Brands by name

Popular brands