background image

©2017 Hestan Commercial Corporation

10

EN

GAS SUPPLY

The local gas authority or supplier should be consulted at the installation planning stage in order to 

establish the availability of an adequate supply of gas (NG or LP).  If it is a new installation, have the 

gas authorities or supplier check the meter size and piping to assure that the unit is supplied with the 

necessary amount of gas supply and pressure to operate the unit(s). 

Gas connections should be made by a qualified plumber, or your professional outdoor appliance installer.

All fixed (non-mobile) appliances must be fitted with an accessible upstream gas shutoff valve as a means of 

isolating the appliance for emergency shut off and for servicing. 

Make certain new piping and connections have been made in a clean manner and have been purged so that 

piping compound, chips, etc. will not clog regulators, valves, orifices, or burners.  Use pipe joint compound 

/ thread sealant approved for natural and LP gases. 

NEVER CONNECT THE SIDE BURNER TO AN UNREGULATED GAS SUPPLY.  Before proceeding, 

ensure the appliance is fitted for Natural or Liquid Propane gas.  Connecting to an improper gas type will 

result in poor performance and increased risk of damage or injury.  Gas type and gas consumption (BTU 

per hour) for each burner type is located on inner right wall of the unit, behind the control panel.

Installation of this cooking appliance must be made in accordance with local codes.  In the absence of local 

codes, this unit should be installed in accordance with the National Fuel Gas Code No. 

Z223.1/ NFPA 54, 

Natural Gas and Propane Installation code 

CSA B149-1, or Propane Storage and Handling Code B149.2.

NOTE:  See rating label for manifold pressure for the type of gas of your appliance.

CONVERSION KITS

Gas conversion kits are available from your Hestan dealer should you need to convert an LP unit to NG, or 

vice-versa.  

HIGH ALTITUDE KITS

If you live in a high altitude area, 2,000 ft. (610 m) or more above sea level, your side burner will require 

different orifices for proper combustion and performance.  High altitude kits are available through Hestan 

Customer Service.  Please have your model and serial number information ready when you call.

GAS AND ELECTRICAL CONNECTIONS

Summary of Contents for ASPIRE AEB Series









































Reviews: