background image

HERZ ETKF+ 

 

 

Page 5 

 

Window  

(1

 8251 

02)

  

 

 

 

 

 

Intended use  

The window  is used to detect when a window is opened. If the window contact is taught-in 
to a energy saving thermostatic head  ETKF+, these devices will automatically reduce the 
temperature in the room during ventilation. Using the automatic temperature reduction function 
whilst windows are open enables heating costs to be lowered. 
The device may only be operated indoors and must be protected from the effects of damp and dust, 
as well as solar or other methods of heat radiation. Using the device for any purpose other  than 
what is described in this operating manual does not fall within the scope of intended use and shall 
invalidate any warranty or liability. This also applies to any conversion or modification work. This 
device is intended for domestic use only.  
 

 

Device Overview 

 

The window  (A+  B) consists of a large electronic unit (A) and a small magnet (B). The 
device is supplied with spacers and caps in white and brown. 
C: Teach-In button 
D: Device LED 

 

Preparing for mounting  

The window  consists of two elements: an electronic unit (A) and a magnet (B). The 
electronic unit (A) must be mounted on the frame and the magnet (B) on the window. This enables 
the electronic unit with a window opening. When the magnet is not in the immediate vicinity, then a 
"window open" signal sent.

 

 
Installation site: 
• First select the window that is frequently used for ventilation and which the window  is to 

be attached to.  

Mounting dimension in mm (W x H x D):  

electronic unit: 18,5 x 103,5 x 24,5 
magnet: 12 x 48 x 12 

Summary of Contents for 8251















Reviews: