manualshive.com logo in svg

HermanMiller Layout Studio GNSDRG Series, Installation And Disassembly For Recycling Instructions

Share
Download
HermanMiller Layout Studio GNSDRG Series Installation And Disassembly For Recycling Instructions Download Page 9

Z

© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.

Part no. 1BG02M rev B.

TM

 

Y

, 

L

, Canvas are among the trademarks of Herman Miller, Inc. 

Illustrations and specifications are based on the latest product information available at the time of publication. 
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 

9

7.  Lower screen down onto rail.

8.  Repeat procedure for the next screen.

9.  Screens should 

fi

 t against each other with minimal gaps.  Do not push them 

     together so tight that they bind up when pushed down.  If there is variable gap 

     between screens, system may not be level or screens may be too close 

     together so they don’t seat properly.

10. Insert Alignment Clips (P).

N

Summary of Contents for Layout Studio GNSDRG Series



















Reviews:

No comments

Brands by name

Popular brands

Load more brands