manualshive.com logo in svg

HermanMiller Layout Studio GNSDRG Series, Installation And Disassembly For Recycling Instructions

Share
Download
HermanMiller Layout Studio GNSDRG Series Installation And Disassembly For Recycling Instructions Download Page 14

Z

© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.

Part no. 1BG02M rev B.

TM

 

Y

, 

L

, Canvas are among the trademarks of Herman Miller, Inc. 

Illustrations and specifications are based on the latest product information available at the time of publication. 
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 

14

3.  Center Glass Screen (X) with work surface.

4.  Firmly press screen into 

fi

 llers and clamps.  Make sure glass is pressed all the 

     way down.

5.  Adjust plumb of screen with set screws by tightening one side and loosening 

     the opposite side.  Make sure all screws are snug against screen. 

X

Set Screw

X

GNSDXG.

AJ

AF

1.  Press seal (AJ) onto bottom edge of glass (X).

2.  Set glass assembly into Screen Rail (AF).

Summary of Contents for Layout Studio GNSDRG Series



















Reviews:

No comments

Brands by name

Popular brands

Load more brands