background image

Specifications for LP Morgan Dipper/Flipper HEX codes

 

Manufactured in Australia, LP Morgan can create a tailor made solution to your requirements. 

For more information check out www.lpmorgan.com.au or call 1300 730 025

Mar 2010 v1.1

DIPPER/ FLIPPER REMOTE HECS CODES 

(HERMA PRODUCT CODE HER20HDIRKIT)

    

IR wavelength is 950 nm. Light is modulated at 38 KHz with 1/3 duty cycle.  

An on pulse must be at least 158 µseconds (µs) long (6 cycles) and 

should not be longer than 448 µs (17 cycles). 
From the start of a pulse till the start of the next pulse is 1050 µs for a “0 

bit”, and 2000 µs for a “1 bit”. 

A Flash is 11 pulses (10 bits), minimum time between flashes (interflash 

time) is 11 mseconds (ms), 30 ms isrecommended.
There is NO preamble.
Channel 1 OPEN sequence is 0101000010 
The sequence always starts with 01, so for simplicity strip that off, and 

we get 0100 0010 = hex 42 

The complete table of codes (in HECS) is

OPEN 1  

0x42    

OPEN 16  

0x48    

OPEN 31  

0x17    

OPEN 46  

0x59 

CLOSE 1  

0x22    

CLOSE 16  

0x28    

CLOSE 31  

0x0f    

CLOSE 46  

0x39 

OPEN 2  

0x62    

OPEN 17  

0x18    

OPEN 32  

0x57    

OPEN 47  

0x01 

CLOSE 2  

0x12    

CLOSE 17  

0x04    

CLOSE 32  

0x37    

CLOSE 47  

0x71 

OPEN 3  

0x32    

OPEN 18  

0x44    

OPEN 33  

0x4f    

OPEN 48  

0x69 

CLOSE 3  

0x0a    

CLOSE 18  

0x24    

CLOSE 33  

0x2f    

CLOSE 48  

0x65 

OPEN 4  

0x4a    

OPEN 19  

0x14    

OPEN 34  

0x5b    

OPEN 49  

0x1d 

CLOSE 4  

0x2a    

CLOSE 19  

0x0c    

CLOSE 34  

0x3b    

CLOSE 49  

0x1e 

OPEN 5  

0x1a    

OPEN 20  

0x54    

OPEN 35  

0x03    

OPEN 50  

0x1f 

CLOSE 5  

0x06    

CLOSE 20  

0x34    

CLOSE 35  

0x73    

CLOSE 50  

0x3c 

OPEN 6  

0x46    

OPEN 21  

0x4c    

OPEN 36  

0x6b    

OPEN 51  

0x3d 

CLOSE 6  

0x26    

CLOSE 21  

0x2c    

CLOSE 36  

0x67    

CLOSE 51  

0x3e 

OPEN 7  

0x16    

OPEN 22  

0x58    

OPEN 37  

0x41    

OPEN 52  

0x3f 

CLOSE 7  

0x0e    

CLOSE 22  

0x38    

CLOSE 37  

0x21    

CLOSE 52  

0x5c 

OPEN 8  

0x56    

OPEN 23  

0x1c    

OPEN 38  

0x61    

OPEN 53  

0x5d 

CLOSE 8  

0x36    

CLOSE 23  

0x70    

CLOSE 38  

0x11    

CLOSE 53  

0x5e 

OPEN 9  

0x4e    

OPEN 24  

0x68    

OPEN 39  

0x31    

OPEN 54  

0x5f 

CLOSE 9  

0x2e    

CLOSE 24  

0x64    

CLOSE 39  

0x09    

CLOSE 54  

0x77 

OPEN 10  

0x5a    

OPEN 25  

0x43    

OPEN 40  

0x49    

OPEN 55  

0x79 

CLOSE 10  

0x3a    

CLOSE 25  

0x23    

CLOSE 40  

0x29    

CLOSE 55  

0x7a 

OPEN 11  

0x02    

OPEN 26  

0x63    

OPEN 41  

0x19    

OPEN 56  

0x7b 

CLOSE 11  

0x72    

CLOSE 26  

0x13    

CLOSE 41  

0x05    

CLOSE 56  

0x6f 

OPEN 12  

0x6a    

OPEN 27  

0x33    

OPEN 42  

0x45    

OPEN 57  

0x7d 

CLOSE 12  

0x66    

CLOSE 27  

0x0b    

CLOSE 42  

0x25    

CLOSE 57  

0x7e 

OPEN 13  

0x40    

OPEN 28  

0x4b    

OPEN 43  

0x15    

OPEN 58  

0x75 

CLOSE 13  

0x20    

CLOSE 28  

0x2b    

CLOSE 43  

0x0d    

CLOSE 58  

0x6d 

OPEN 14  

0x60    

OPEN 29  

0x1b    

OPEN 44  

0x55    

OPEN 59  

0x78 

CLOSE 14  

0x10    

CLOSE 29  

0x07    

CLOSE 44  

0x35    

CLOSE 59  

0x7c 

OPEN 15  

0x30    

OPEN 30  

0x47    

OPEN 45  

0x4d    

OPEN 60  

0x74 

CLOSE 15  

0x08    

CLOSE 30  

0x27    

CLOSE 45  

0x2d    

CLOSE 60  

0x6c 

 

 

 

 

 

 

 

OPEN ALL  

0x76    

CLOSE ALL   0x6e    

STOP   

0x52    

WIND    

0x50 

Summary of Contents for LP Morgan Dipper






























Reviews: